RF2713 Ver la hoja de datos (PDF) - RF Micro Devices

Número de pieza

componentes Descripción

Lista de partido

RF2713

QUADRATURE MODULATOR/DEMODULATOR

RF Micro Devices 

RF2713

Absolute Maximum Ratings

Parameter

Supply Voltage

IF Input Level

Operating Ambient Temperature

Storage Temperature

Rating

-0.5 to 7.0

500

-40 to +85

-40 to +150

Unit

VDC

mVPP

°C

°C

Caution! ESD sensitive device.

Exceeding any one or a combination of the Absolute Maximum Rating conditions may

cause permanent damage to the device. Extended application of Absolute Maximum

Rating conditions to the device may reduce device reliability. Specified typical perfor-

mance or functional operation of the device under Absolute Maximum Rating condi-

tions is not implied.

RoHS status based on EUDirective2002/95/EC (at time of this document revision).

The information in this publication is believed to be accurate and reliable. However, no

responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any

infringement of patents, or other rights of third parties, resulting from its use. No

license is granted by implication or otherwise under any patent or patent rights of

RFMD. RFMD reserves the right to change component circuitry, recommended appli-

cation circuitry and specifications at any time without prior notice.

Parameter

Overall

IF Frequency Range

Specification

Min.

Typ.

Max.

0.1

265

Baseband Frequency Range

Input Impedance

LO

Frequency

DC

50

1200 || 1pF

Level

Input Impedance

Demodulator Configuration

Output Impedance

Maximum Output

Voltage Gain

Noise Figure

0.06

22.5

500 || 1pF

170 || 1pF

2.5

20

24

24

0.8

25.1

Input Third Order Intercept Point

(IIP3)

28

33

-22

-11

-19

-8

-28

Unit

MHz

MHz

Ω

Condition

T=25°C, VCC=3.0V, IF=100MHz,

LO=200MHz, FMOD=500kHz

For IF frequencies below ~2.5MHz, the LO

should be a square wave. IF frequencies lower

than 100kHz are attainable if the LO is a

square wave and sufficiently large DC blocking

capacitors are used.

Each input, single-ended

VPP

Ω

Ω

VPP

dB

dB

dB

dB

dBm

dBm

dBm

dBm

Twice (2x) the IF frequency. For IF frequencies

below ~2.5MHz, the LO should be a square

wave. IF frequencies lower than 100kHz are

attainable if the LO is a square wave and suffi-

ciently large DC blocking capacitors are used.

IFIN=28mVPP, LO=200mVPP, ZLOAD=10kΩ

Each output, IOUT and QOUT @ 1MHz

Saturated

VCC = 3.0 V

VCC = 5.0 V

Single Sideband, IF Input of device reactively

matched

Single Sideband, 50Ω shunt resistor at IF Input

VCC=3.0V, IF Input of device reactively

matched

VCC=3.0V, 50Ω shunt resistor at IF Input

VCC=5.0V, IF Input of device reactively

matched

VCC=5.0V, 50Ω shunt resistor at IF Input

VCC=5.0V, IF Input of device reactively

matched, ZLOAD=50Ω

2 of 16

7628 Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical

support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com.

Rev A5 DS061016

Share Link: