HS-82C55ARH(1995) Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Lista de partido
HS-82C55ARH Datasheet PDF : 23 Pages
| |||
Specifications HS-82C55ARH
Absolute Maximum Ratings
Reliability Information
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V
Input, Output or I/O Voltage . . . . . . . . . . . . .VSS-0.3V to VDD+0.3V
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance
θJA
SBDIP Package. . . . . . . . . . . . . . . . . . . . 40oC/W
θJC
6oC/W
Maximum Package Power Dissipation at +125oC Ambient
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.25W
If device power exceeds package dissipation capability, provide heat
sinking or derate linearly at the following rate:
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25.0mW/C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC
Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to +0.8V
Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . . VDD -1.5V to VDD
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
TTL Output High Voltage
CMOS Output High Volt-
age
Output Low Voltage
Input Leakage Current
Output Leakage Current
Input Current Bus Hold
High
Input Current Bus Hold
Low
Standby Power Supply
Current
Darlington Drive Voltage
Functional Tests
Noise Immunity Functional
Test (Note 4)
SYMBOL
VOH1
VOH2
VOL
IIL or IIH
IOZL or
IOZH
IBHH
IBHL
IDDSB
VDAR
FT
FN
CONDITIONS
GROUP A
SUBGROUP
VDD = 4.5V, IO = -2.5mA,
VIN = 0V, 4.5V
1, 2, 3
VDD = 4.5V, IO = -100µA,
VIN = 0V, 4.5V
1, 2, 3
VDD = 4.5V, IO = 2.5mA,
VIN = 0V, 4.5V
1, 2, 3
VDD = 5.5V, VIN = 0V, 5.5V
1, 2, 3
VDD = 5.5V, VIN = 0V, 5.5V
1, 2, 3
VDD = 4.5V or 5.5V,
VIN = 3.0V (See Note 1)
Ports A, B, C
VDD = 4.5V or 5.5V,
VIN = 1.0V (See Note 2)
Port A
VDD = 5.5V, IO = 0mA,
VIN =GND or VDD
VDD = 4.5V, IO = -2.0mA,
VIN = GND or VDD
VDD = 4.5V and 5.5V,
VIN = GND or VDD,
f = 1MHz
VDD = 5.5V, VIN = GND or
VDD - 1.5V and
VDD = 4.5V, VIN = 0.8V or
VDD
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
7, 8A, 8B
7, 8A, 8B
LIMITS
TEMPERATURE MIN MAX UNITS
-55oC, +25oC,
3.0
-
V
+125oC
-55oC, +25oC, VDD- -
V
+125oC
0.4
-55oC, +25oC,
-
0.4
V
+125oC
-55oC, +25oC, -1.0 1.0
µA
+125oC
-55oC, +25oC,
-10
10
µA
+125oC
-55oC, +25oC, -800 -60
µA
+125oC
-55oC, +25oC,
60 800
µA
+125oC
-55oC, +25oC,
-
20
µA
+125oC
-55oC, +25oC,
3.9
-
V
+125oC
-55oC, +25oC,
-
-
-
+125oC
-55oC, +25oC,
-
-
-
+125oC
NOTES:
1. IBHH should be measured after raising VIN and then lowering to 3.0V.
2. IBHL should be measured after lowering VIN to VSS and then raising to 0.8V.
3. No internal current limiting exists on the Port Outputs. A resistor must be added externally to limit the current.
4. For VIH (VDD = 5.5V) and VIL (VDD = 4.5V) each of the following groups is tested separately with all other inputs using VIH = 2.6V,
VIL = 0.4V: PA, PB, PC, Control Pins (Pins 5, 6, 8, 9, 35, 36).
Spec Number 518060
972
Share Link: 