UPJ1E471MDD Ver la hoja de datos (PDF) - Nichicon
Número de pieza
componentes Descripción
Lista de partido
UPJ1E471MDD Datasheet PDF : 7 Pages
| |||
ALUMINUM ELECTROLYTIC CAPACITORS
PJ Low Impedance, For Switching Power Supplies
series
Low impedance and high reliability withstanding 5000 hours load life
at +105˚C (3000 / 2000 hours for smaller case sizes as specified below).
Capacitance ranges available based on the numerical values in E12 series under JIS.
Ideally suited for use of switching power supplies.
Compliant to the RoHS directive (2011/65/EU).
PJ
Smaller
Specifications
PS
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Performance Characteristics
–55 to +105˚C (6.3 to 100V), –40 to +105˚C (160 to 400V), –25 to +105˚C (450V)
6.3 to 450V
0.47 to 15000µF
± 20% at 120Hz, 20˚C
Rated Voltage (V)
6.3 to 100
Leakage current After 1 minute's application of rated voltage at 20°C, leakage current is
not more than 0.03CV or 4 (µA), whichever is greater.
160 to 450
CV <= 1000 : I = 0.1CV+40 (µA) max.
CV > 1000 : I = 0.04CV+100 (µA) max.
Rated Voltage (V)
6.3
10
16
25
35
tan δ (MAX.)
0.22
0.19
0.16
0.14
0.12
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.
50
0.10
120Hz, 20˚C
63 to 100 160 to 350 400 • 450
0.08
0.20
0.25
Rated voltage (V)
6.3 • 10
16
25• 35 50 to 100 160• 200 250 315• 350 400
Stability at Low Temperature Impedance
Z– 25˚C / Z+20˚C —
—
—
—
—
—
—
—
ratio (MAX.)
Z– 40˚C / Z+20˚C —
—
—
—
4
6
8
10
Z–55˚C / Z+20˚C
4
3
3
2
—
—
—
—
450 120Hz
15
—
—
Endurance
Shelf Life
Marking
The specifications listed at right shall be met when the
capacitors are restored to 20˚C after D.C. bias plus rated ripple
current is applied for 5000 hours (2000 hours for φD=5 and 6.3,
3000 hours for φD=8) at 105˚C, the peak voltage shall not
exceed the rated voltage.
After storing the capacitors under no load at 105˚C for 1000
hours and then performing voltage treatment based on JIS C
5101-4 clause 4.1 at 20°C, they shall meet the specified
values for the endurance characteristics listed at right.
Printed with white color letter on dark brown sleeve.
Capacitance change Within ±20% of the initial capacitance value
tan δ
200% or less than the initial specified value
Leakage current
Less than or equal to the initial specified value
Capacitance change Within ±20% of the initial capacitance value
tan δ
150% or less than the initial specified value
Leakage current
Less than or equal to the initial specified value
Radial Lead Type
Type numbering system (Example : 25V 470µF)
Sleeve (P.E.T.)
φd
Sleeve(P.V.C)
φd tinned CP wire
Pressure
relief vent
(φ6.3up)
L + MAX.
Pre1rleie5sfsMvuerenINt
(φ6.3UP)
L+ M4AMXIN
15MIN
4MIN
123
UP J
123 45
UP J 1E
4 5 6 7 8 9 10 11 12
Type
Code
1 E 4 7 1 MPD
Small Dia
Low Profile
6
6 7 8 9 10 11 12
Size code
4 7 1 MHH 6
Configuration
Configuration
Capacitance tolerance (±20%)
Case size code
Configuration
Rated capacitance (470µF)
Type φ D
Pb-free leadwire
PCbo-dfreee PET sleeve
Capacitance tolerance(±20%) φD Code
Small Dia 5
DD
Rated Capacitance(470µRF)ated v5oltageD(H25V)
6.3
EH
Low Profile
6.3
6
ED
Rated voltage(25V) 8.1S0 eriePsHname
8 • 10
PD
Series name 12.5~18 HH
Type
12.5 to 18
HD
Type
(φD < 10) 1.0
(φD 10) 1.5
Frequency coefficientRated voRlatategdevoltage
of rated ripple current
(mm)
φD
5
6.3
8
10 In ca1s2e.5L >251fo6r the φ1128.5 dia. unit, lead dia. φ d=0.8mm.
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
φd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
In case L >25 for the φ12.5 dia. unit, lead dia. φ d=0.8mm.
• Please refer to page 20 about the end seal configuration.
6.3 to 100V
(10kHz to
200kHz = 1)
6.3 to 100V
(10kHz to
200kHz=1)
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 4 for the minimum order quantity.
Dimension table in next pages.
160 to 450V
15000
1501000000
FFrreeqqueunecnyccyoecffoiceiefnfitcient
100060800
68040700
3300
4700
2200
33010500
22010000
1500680
470
1000
330
680220
470150
330100
68
220
47
150 33
100 22
120Hz
300Hz
1kHz
68 15
10
47
0.68
330.47
22 0
15
120Hz
300Hz
0.5 0.6 0.7 0.8
Frequency coefficient
1kHz
0.9 1.0
50H1z0
0.08.068
0.47
120Hz
1.00
300Hz
1.25
1kHz
1.40
10kHz or more
1.60
0
CAT.8100D 0.5 0.6 0.7 0.8 0.9 1.0
Frequency coefficient
Share Link: 