PI5A385A Ver la hoja de datos (PDF) - Pericom Semiconductor Corporation
Número de pieza
componentes Descripción
Lista de partido
PI5A385A
Pericom Semiconductor Corporation
PI5A385A Datasheet PDF : 8 Pages
| |||
PI5A381A
PI5A383A
PI5A385A 111222333444555666777888999000111222333444555666777888999000111222333444555666777888999000111222111222333444555666777888999000111222333444555666777888999000111222333444555666777888999000111222111222333444555666777888999000111222333444555666777888999000111222333444555666777888999000111222111222333444555666777888999000111222333444555666777888999000111222333444555666777888999000111222111222333444555666777888999000111222
Absolute Maximum Ratings
Voltages Referenced to GND
VCC ...................................................................................................................................................................................................................–...0...5.V to +7V
VIN,VCOM,VNC,VNO (Note 1) ................................ –0.5V to VCC+2V
................................................... or 30mA, whichever occurs first
Current (any terminal except COM, NO, NC) .................... 30mA
Current, COM, NO, NC ................................................... 100 mA
(pulsed at 1ms, 10% duty cycle) ....................................... 120mA
Thermal Information
Continuous Power Dissipation
PDIP (derate 10.5mW/ºC above 70ºC) ............................. 800mW
Narrow SO & QSOP
(derate 8.7mW/ºC above +70ºC) ...................................... 650mW
Storage Temperature ........................................... -65ºC to +150ºC
Lead Temperature(soldering, 10s) .................................... +300ºC
Note 1 : Signals on NC, NO, COM, or IN exceeding V or GND
CC
are clamped by internal diodes. Limit forward diode current to
30mA.
Caution: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating
and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied.
Electrical Characteristics-Single 5.0V Supply
(VCC = 5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V)
Parameter
Symbol Test Conditions
Temp(ºC) Min.(2) Typ.(2) Max.(2) Unit
Analog Switch
Analog Signal Range(3)
VANALOG
Full
ON-Resistance
On-Resistance Match
Between Channels(4)
25
RON
VCC = 4.5V, ICOM = -30mA
Full
VNO or VNC = +2.5V
25
∆RON
Full
0
V
V
CC
8
10
12
0.9
2
Ω
4
On-ResistanceFlatness(5)
R
FLAT(ON)
VCC = 5V, ICOM = -30mA
VNO or VNC = 1V, 2.5V, 4V
25
Full
3
4
5
NO or NC Off
LeakageCurrent(6)
COM Off
Leakage Current(6)
COM On
Leakage Current(6)
INO(OFF)
VCC = 5.5V, VCOM = 0V
25
INC(OFF)
VNO or VNC = 4.5V
Full
ICOM(OFF)
V+ = 5.5V, V = +4.5V
COM
VNO or VNC = ±0V
25
Full
ICOM(ON) VCC = 5.5V, VCOM = +4.5V
25
VNO or VNC = +4.5V
Full
0.05
-80
80
0.05
nA
-80
80
0.07
-80
80
33
PS7062D 07/14/98
Share Link: