XC641A Ver la hoja de datos (PDF) - TOREX SEMICONDUCTOR

Número de pieza

componentes Descripción

Lista de partido

XC641A

VR x 4,VD x 2 Multi Power Supply

TOREX SEMICONDUCTOR 

■Directions for use

GNotes on Use :

IC

1. Please sufficiently strengthen the GND wiring and the power supply (VDD) line, as when the power

supply line impedance is high, the voltage regulators and detectors are prone to oscillation leading

to possible instability.

2. In order to lower the power supply line impedance, we recommend that a capacitor of 10µF (Tantalum)

or more be connected at the shortest point possible between the VDD pin and the GND pin.

3. To protect the IC from surge at the input pin, an input protect diode is built-in. Therefore, do not

apply voltages that exceed the VDD pin voltage.

4. Please ensure that the sum total of the IC's power consumption does not exceed the stipulated figure

for total continuous power dissipation ( Pd ).

Pd < P1 + P2 + P3 + P4 + P5 + P6

The following equations can be used to calculate the IC's power consumption :

Regulator 1 : P1 = ( VDD - 0.6V ) x IEXT1, IEXT1 to IOUT1 / hFE

Regulator 2 : P2 = ( VDD - 0.6V ) x IEXT2, IEXT2 to IOUT2 / hFE

Regulator 3 : P3 = ( VDD - VOUT3 ) x IOUT3

Regulator 4 : P4 = ( VDD - VOUT4 ) x IOUT4

Detector 1 : P5 = VDOUT1 x IDOUT1

Detector 2 : P6 = VDOUT2 x IDOUT2

Voltage Regulator 1, 2 ( External transistor type )

1. In order to prevent regulator oscillation ( caused by power supply impedance ), we recommend

that a capacitor of 10µF (Tantalum) or more be connected between the external transistor's emitter

and the GND pin.

2. In order to prevent regulator phase compensation, we recommend that a capacitor of 10µF (Tantalum)

or more be connected between the IOUT1, IOUT2 pins and the GND pin.

3. In order to prevent oscillation we recommend that a resistor of around 200kΩ be connected between

the external transistor's base pin and emitter pin.

Voltage Regulator 3, 4 ( Built-in transistor type )

1. Please connect a capacitor of 1µF (Tantalum) or more between the voltage regulator's output pins

( OUT3, OUT4 ) and the GND pin.

2. In order to prevent regulator oscillation ( caused by power supply impedance ), we recommend that

a capacitor be connected between the VDD pin and the GND pin.

3. Since a short circuit protector is not built-in, when the OUT3 or OUT4 pin is short circuited to the

GND pin, resulting surge current may damage the IC.

Voltage Detectors

1. In order to prevent regulator oscillation ( caused by power supply impedance ), we recommend

that a capacitor be connected between the VDD pin and the GND pin.

2. Should the VDD pin voltage become excessively low, we recommend that a Schottky Diode be

connected between the CD1 pin and the VDD pin, in order to prevent voltages over the established

VDD + 0.3V being applied to the capacitor connection pin ( CD1 ).

Please use a Schottky Diode of VF = 0.3V ( IF = 10mA ). If a large reverse current, IR (max.), is used,

the delay circuit current will increase and delay time will be shortened.

3. When not using the delay circuit, please use the IC with the CD1 pin open.

XC641A

Series

10

657

Share Link: