9517A Ver la hoja de datos (PDF) - NXP Semiconductors.
Número de pieza
componentes Descripción
Lista de partido
9517A Datasheet PDF : 22 Pages
| |||
NXP Semiconductors
PCA9517A
Level translating I2C-bus repeater
Table 5. Static characteristics …continued
VCC = 2.7 V to 5.5 V; GND = 0 V; Tamb = 40 C to +85 C; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Enable
VIL
VIH
IIL(EN)
LOW-level input voltage
HIGH-level input voltage
LOW-level input current on
pin EN
VI = 0.2 V, EN; VCC = 3.6 V
0.5
-
0.7VCC(B) -
-
10
ILI
input leakage current
Ci
input capacitance
VI = 3.0 V or 0 V
1
-
-
6
Max
Unit
+0.3VCC(B) V
5.5
V
30
A
+1
A
7
pF
[1] LOW-level supply voltage.
[2] VIL specification is for the first LOW level seen by the SDAB/SCLB lines. VILc is for the second and subsequent LOW levels seen by the
SDAB/SCLB lines.
[3] VIL for port A with envelope noise must be below 0.3VCC(A) for stable performance.
10. Dynamic characteristics
Table 6. Dynamic characteristics
VCC = 2.7 V to 5.5 V; GND = 0 V; Tamb = 40 C to +85 C; unless otherwise specified.[1][2]
Symbol Parameter
Conditions
Min
tPLH
LOW to HIGH propagation delay
port B to port A; Figure 13
[4] 100
tPHL
HIGH to LOW propagation delay
port B to port A; Figure 11
VCC(A) 2.7 V
[5] 30
VCC(A) 3 V
10
tTLH
LOW to HIGH output transition time port A; Figure 11
10
tTHL
HIGH to LOW output transition time port A; Figure 11
VCC(A) 2.7 V
[5] 1
VCC(A) 3 V
tPLH
LOW to HIGH propagation delay
port A to port B; Figure 12
tPHL
HIGH to LOW propagation delay
port A to port B; Figure 12
20
[6] 25
[6] 60
tTLH
LOW to HIGH output transition time port B; Figure 12
120
tTHL
HIGH to LOW output transition time port B; Figure 12
30
tsu
set-up time
EN HIGH before START condition [7] 100
th
hold time
EN HIGH after STOP condition
[7] 100
Typ[3] Max
170 250
80
110
66
300
20
30
77
105
70
175
53
110
79
230
140 170
48
90
-
-
-
-
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
[1] Times are specified with loads of 1.35 k pull-up resistance and 57 pF load capacitance on port B, and 167 pull-up resistance and
57 pF load capacitance on port A. Different load resistance and capacitance will alter the RC time constant, thereby changing the
propagation delay and transition times.
[2] Pull-up voltages are VCC(A) on port A and VCC(B) on port B.
[3] Typical values were measured with VCC(A) = 3.3 V at Tamb = 25 C, unless otherwise noted.
[4] The tPLH delay data from port B to port A is measured at 0.5 V on port B to 0.5VCC(A) on port A when VCC(A) is less than 2 V, and 1.5 V
on port A if VCC(A) is greater than 2 V.
[5] Typical value measured with VCC(A) = 2.7 V at Tamb = 25 C.
[6] The proportional delay data from port A to port B is measured at 0.3VCC(A) on port A to 1.5 V on port B.
[7] The enable pin, EN, should only change state when the global bus and the repeater port are in an idle state.
PCA9517A
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 4.1 — 24 May 2016
© NXP Semiconductors N.V. 2016. All rights reserved.
11 of 22
Share Link: 