IP101GR Ver la hoja de datos (PDF) - Unspecified
Número de pieza
componentes Descripción
Lista de partido
IP101GR Datasheet PDF : 65 Pages
| |||
IP101G
Preliminary Data Sheet
Revision History
Revision #
Change Description
IP101G-DS-R01
Initial release.
IP101G-DS-R01-20120522 1) Correct the typo of Digital IO Pin Control Register.
2) Modify the operation voltage REGOUT and DVDD_REGIN of DC
Characteristics.
IP101G-DS-R01-20120611 1)
2)
3)
4)
5)
Correct the typo of Linear Regulator Output Control Register.
Correct the typo of pin description for pin type PD and PU.
Modify the register description for RMII_V12 and RMII_V10.
Correct the typo of register default values.
Modify the operation voltage DVDD33_IO of DC Characteristics.
IP101G-DS-R01-20120622 Add 30 seconds into the definition for register WOL_PLUS_TIMER_SEL.
IP101G-DS-R01-20120629 Add the symbol SC (Self Clear) for PHY MII register 0.15 Reset and 0.9
Restart Auto-Negotiation.
IP101G-DS-R01-20120709 1)
2)
3)
4)
5)
6)
Add LED mode 2 in the pin description and function description.
Correct the table of LED Blink Timing.
Add more description of PHY Address Configuration and IEEE 802.3az.
Add ESD reliability of Absolute Maximum Rating.
Correct the typo of function description for Auto Power Saving Mode.
Change register P16R16[10] description from HEART_BEAT_EN to
Reserved.
IP101G-DS-R01-20120719 Correct the table of Register Map for page selection.
IP101G-DS-R01-20120726 1)
2)
3)
Add more description of Register RX2TX_LPBK P1R23[13] for Rx to Tx
loopback test.
Add more description on Fiber Mode Setting and latched-in pin signals
on AC Timing.
Add IP101AH into the table of features comparison.
IP101G-DS-R01-20120808 1) Correct the I/O type of IP101GA pin description to O(Ouput) for pin24
RXER.
2) Change the pin name from DVDD33_IO to VDDIO.
IP101G-DS-R01-20120821 1) Change the default value of register P16R27 from 0x0022 to 0x0012.
2) Remove I/O Slew Rate Control Register.
3) Change the register location RMII_WITH_ER from P16R29[0] to
P16R29[7].
IP101G-DS-R01-20120927 1) Add more description of low power idle (LPI) state in MII and RMII
modes.
2) Correct the typo of Physical Dimensions.
IP101G-DS-R01-20121101 Change the LED blink timing from “On 80ms -> Off (20~40)ms” to “On 26ms
-> Off 78ms”.
IP101G-DS-R01-20121113 Add more function description to support Jumbo Frame.
IP101G-DS-R01-20121127 Change the LED mode function as same as IP101A.
IP101G-DS-R01-20121224 Add the notice that does not let these PHY address pins floating for the
latched-in settings after the power is ready.
Disclaimer
This document probably contains the inaccurate data or typographic error. In order to keep this
document correct, IC Plus reserves the right to change or improve the content of this document.
6/65
December 24 2012
Copyright © 2011, IC Plus Corp.
IP101G-DS-R01
www.BDTIC.com/ICplus
Share Link: 