74ABT652A Ver la hoja de datos (PDF) - Philips Electronics
Número de pieza
componentes Descripción
Lista de partido
74ABT652A Datasheet PDF : 8 Pages
| |||
Philips Semiconductors
Octal transceiver/register, non-inverting (3-State)
Product specification
74ABT652A
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
VCC
VI
VIH
VIL
IOH
IOL
∆t/∆v
Tamb
DC supply voltage
Input voltage
High-level input voltage
Low-level input voltage
High-level output current
Low-level output current
Input transition rise or fall rate
Operating free-air temperature range
LIMITS
Min
Max
4.5
5.5
0
VCC
2.0
0.8
–32
64
0
10
–40
+85
UNIT
V
V
V
V
mA
mA
ns/V
°C
DC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Tamb = +25°C
Tamb = –40°C
to +85°C
UNIT
Min Typ Max Min Max
VIK
Input clamp voltage
VCC = 4.5V; IIK = –18mA
–0.9 –1.2
–1.2 V
VCC = 4.5V; IOH = –3mA; VI = VIL or VIH
2.5 3.0
2.5
V
VOH High–level output voltage
VCC = 5.0V; IOH = –3mA; VI = VIL or VIH
3.0 3.5
3.0
V
VCC = 4.5V; IOH = –32mA; VI = VIL or VIH
2.0 2.4
2.0
V
VOL Low–level output voltage
VCC = 4.5V; IOL = 64mA; VI = VIL or VIH
0.3 0.55
0.55 V
VRST3 Power-up output low voltage VCC = 5.5V; IO = 1mA; VI = GND or VCC
0.13 0.55
0.55 V
II
Input leakage Control pins VCC = 5.5V; VI = GND or 5.5V
current
Data pins
VCC = 5.5V; VI = GND or 5.5V
IOFF
Power-off leakage current
VCC = 0.0V; VO or VI ≤ 4.5V
±0.01
±5
±5.0
±1.0
±100
±100
±1.0 µA
±100 µA
±100 µA
IPU/IPD
Power-up/down 3-State
output current4
VCC = 2.1V; VO = 0.5V; VI = GND or VCC ;
VOE = Don’t care; VOE = Don’t care
±5.0 ±50
±50 µA
IIH + IOZH 3–State output High current VCC = 5.5V; VO = 2.7V; VI = VIL or VIH
5.0 50
50
µA
IIL + IOZL 3–State output Low current VCC = 5.5V; VO = 0.5V; VI = VIL or VIH
–5.0 –50
–50 µA
ICEX
IO
Output High leakage current
Output current1, 5
VCC = 5.5V; VO = 5.5V; VI = GND or VCC
VCC = 5.5V; VO = 2.5V
5.0 50
50
µA
–40 –65 –180 –40 –180 mA
ICCH
VCC = 5.5V; Outputs High, VI = GND or VCC
110 250
250 µA
ICCL Quiescent supply current
VCC = 5.5V; Outputs Low, VI = GND or VCC
20
30
30 mA
ICCZ
VCC = 5.5V; Outputs 3-State;
VI = GND or VCC
110 250
250 µA
∆ICC
Additional supply current per VCC = 5.5V; one input at 3.4V,
input pin2
other inputs at VCC or GND; VCC = 5.5V
0.3 1.5
1.5 mA
NOTES:
1. Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
2. This is the increase in supply current for each input at 3.4V.
3. For valid test results, data must not be loaded into the flip-flops (or latches) after applying the power.
4. This parameter is valid for any VCC between 0V and 2.1V, with a transition time of up to 10msec. From VCC = 2.1V to VCC = 5V ± 10%, a
transition time of up to 100µsec is permitted.
5. This data sheet limit may vary among suppliers.
1995 Apr 19
5
Share Link: 