74ALVT16899 Ver la hoja de datos (PDF) - Philips Electronics

Número de pieza

componentes Descripción

Lista de partido

74ALVT16899

2.5V/3.3V 18-bit latched transceiver with 16-bit parity generator/checker (3-State)

Philips Electronics 

Philips Semiconductors

2.5V/3.3V 18-bit latched transceiver with 16-bit parity

generator/checker (3-State)

Product specification

74ALVT16899

DC ELECTRICAL CHARACTERISTICS (3.3V "0.3V RANGE)

LIMITS

SYMBOL

PARAMETER

TEST CONDITIONS

Temp = -40°C to +85°C UNIT

MIN TYP1 MAX

VIK

Input clamp voltage

VCC = 3.0V; IIK = –18mA

–0.85 –1.2

V

VOH

High-level output voltage

VCC = 3.0 to 3.6V; IOH = –100µA

VCC = 3.0V; IOH = –32mA

VCC–0.2 VCC

V

2.0

2.3

VCC = 3.0V; IOL = 100µA

0.07 0.2

VOL

Low–level output voltage

VCC = 3.0V; IOL = 16mA

VCC = 3.0V; IOL = 32mA

0.25 0.4

V

0.3 0.5

VCC = 3.0V; IOL = 64mA

0.4 0.55

VRST Power-up output low voltage6 VCC = 3.6V; IO = 1mA; VI = VCC or GND

0.55

V

VCC = 3.6V; VI = VCC or GND

VCC = 0 or 3.6V; VI = 5.5V

Control pins

0.1

±1

0.1

10

II

Input leakage current

VCC = 3.6V; VI = 5.5V

VCC = 3.6V; VI = VCC

Data pins4

0.1

20

µA

0.5

1

VCC = 3.6V; VI = 0V

0.1

-5

IOFF

Off current

VCC = 0V; VI or VO = 0 to 4.5V

0.1 ±100 µA

IHOLD

Bus Hold current

Data inputs

VCC = 3V; VI = 0.8V

VCC = 3V; VI = 2.0V

VI = 0V to 3.6V; VCC = 3.6V7

75

130

–75 –140

µA

±500

IEX

Current into an output in the

High state when VO > VCC

VO = 5.5V; VCC = 3.0V

10

125

µA

IPU/PD

Power up/down 3-State output VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC

current3

OE/OE = Don’t care

33 ±100 µA

IOZH 3-State output High current

VCC = 3.6V; VO = 3.0V; VI = VIL or VIH

0.5

5

µA

IOZL

3-State output Low current

VCC = 3.6V; VO = 0.5V; VI = VIL or VIH

0.5

–5

µA

ICCH

VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0

0.05 0.1

ICCL

Quiescent supply current

VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0

4.6 7.0 mA

ICCZ

VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05

0.06 0.1

∆ICC

Additional supply current per

input pin2

VCC = 3V to 3.6V; One input at VCC–0.6V,

Other inputs at VCC or GND

0.04 0.4 mA

NOTES:

1. All typical values are at VCC = 3.3V and Tamb = 25°C.

2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND

3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a

transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.

4. Unused pins at VCC or GND.

5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.

6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.

7. This is the bus hold overdrive current required to force the input to the opposite logic state.

1998 Jun 30

7

Share Link: