ADM1065ACPZ(RevD) Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

fabricante

ADM1065ACPZ
(Rev.:RevD)

Super Sequencer and Monitor

Analog Devices 

ADM1065

Parameter

PROGRAMMABLE DRIVER OUTPUTS

High Voltage (Charge Pump) Mode

(PDO1 to PDO6)

Output Impedance

VOH

IOUTAVG

Standard (Digital Output) Mode

(PDO1 to PDO10)

VOH

VOL

IOL 2

ISINK2

RPULL-UP

ISOURCE (VPx)2

Three-State Output Leakage Current

Oscillator Frequency

DIGITAL INPUTS (VXx, A0, A1)

Input High Voltage, VIH

Input Low Voltage, VIL

Input High Current, IIH

Input Low Current, IIL

Input Capacitance

Programmable Pull-Down Current,

IPULL-DOWN

SERIAL BUS DIGITAL INPUTS (SDA, SCL)

Input High Voltage, VIH

Input Low Voltage, VIL

Output Low Voltage, VOL2

SERIAL BUS TIMING3

Clock Frequency, fSCLK

Bus Free Time, tBUF

Start Setup Time, tSU;STA

Stop Setup Time, tSU;STO

Start Hold Time, tHD;STA

SCL Low Time, tLOW

SCL High Time, tHIGH

SCL, SDA Rise Time, tR

SCL, SDA Fall Time, tF

Data Setup Time, tSU;DAT

Data Hold Time, tHD;DAT

Input Low Current, IIL

SEQUENCING ENGINE TIMING

State Change Time

Min

Typ

500

11

12.5

10.5

12

20

2.4

VPU − 0.3

0

16

20

90

100

2.0

−1

5

20

2.0

1.3

0.6

0.6

0.6

1.3

0.6

100

5

10

Max

Unit Test Conditions/Comments

kΩ

14

V

IOH = 0 μA

13.5

V

IOH = 1 μA

μA 2 V < VOH < 7 V

V

VPU (pull-up to VDDCAP or VPx) = 2.7 V, IOH = 0.5 mA

4.5

V

VPU to VPx = 6.0 V, IOH = 0 mA

V

VPU ≤ 2.7 V, IOH = 0.5 mA

0.50

V

IOL = 20 mA

20

mA Maximum sink current per PDO pin

60

mA Maximum total sink for all PDO pins

29

kΩ Internal pull-up

2

mA Current load on any VPx pull-ups, that is, total

source current available through any number of

PDO pull-up switches configured onto any one

VPx pin

10

μA VPDO = 14.4 V

110

kHz All on-chip time delays derived from this clock

V

Maximum VIN = 5.5 V

0.8

V

Maximum VIN = 5.5 V

μA VIN = 5.5 V

1

μA VIN = 0 V

pF

μA VDDCAP = 4.75 V, TA = 25°C if known logic state

is required

V

0.8

V

0.4

V

IOUT = −3.0 mA

400

kHz

μs

μs

μs

μs

μs

μs

300

ns

300

ns

ns

ns

1

μA VIN = 0 V

μs

1 At least one of the VH, VPx pins must be ≥3.0 V to maintain the device supply on VDDCAP.

2 Specification is not production tested but is supported by characterization data at initial product release.

3 Timing specifications are guaranteed by design and supported by characterization data.

Rev. D | Page 5 of 28

Share Link: