HIP1031 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Lista de partido
HIP1031 Datasheet PDF : 4 Pages
| |||
HIP1031
Absolute Maximum Ratings
Supply Voltage, VCC. . . . . . . . . . . See O.V. Shutdown Limit, VOVSD
Input Voltage, VIN (Note 1) . . . . . . . . . . . . . . . . . . . . . . -0.8V to +7V
Load Current, IOUT . . . . . . . . . . . . . . . . . . . . . . . Internally Limiting
Load Dump (Survival) . . . . . . . . . . . . . . . . . . . . . . . . . . ±60VPEAK
Reverse Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -16V
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W) θJC (oC/W)
Plastic SIP Package . . . . . . . . . . . . . .
50
4
Maximum Power Dissipation, (Note 3)
At TA =
Maximum
125oC, Infinite Heat Sink.
Junction Temperature, TJ
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6.25W
150oC
Maximum Storage Temperature Range . . . . . . . . . .-40oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. The Input Control Voltage, VIN, may range from -0.85V to +7V for a VCC supply voltage of 0V to +25V.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
3. The worst case thermal resistance, θJC for the SIP TS-001AA 5 pin package is 4oC/W. The calculation for dissipation and junction
temperature rise due to dissipation is:
PD = (VCC-VOUT)(IOUT) + (VCC)(ICCMAX - IOUT) or (VCC)(ICCMAX) - (VOUT)(IOUT)
TJ = TAMBIENT + (PD) (θJC) for an infinite Heat Sink.
Refer to Figure 1 for Derating based on Dissipation and Thermal Resistance. Derating from 150oC is based on the reciprocal of thermal
resistance, θJC+θHS.
junction-to-air thermal
rFesoirsetaxnacmep, lθeJ:AW=h1e0reoCθ/JWC.=T4hoeCre/Wforea,nfdorgtivheenmθaHxSim=u6mo/aWlloawsetdheditshseiprmataiol nre, sdiesrtaantece0.o1fWa/noCexftoerrneaalcHh edaetgSreinekf,rothme
TAMB to the maximum rated junction temperature of 150oC. If TAMB = 100oC, the maximum PD is (150 - 100) x 0.1W/oC = 5W.
Electrical Specifications TA = -40οC to 125οC, VIN = 2V, VCC = +12V, Unless Otherwise Specified
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX UNITS
Operating Voltage Range
Over-Voltage Shutdown
Over-Temperature Limiting
Negative Pulse
Output Clamp Voltage
Short Circuit Current Limiting
Input Control ON
Input Control OFF
Input Current High
Input Current Low
Supply Current, Full Load,
Input Control ON
VCC
VOVSD
TSD
VCL
ISC
VIH
VIL
IIH
IIL
ICCMAX
4.5
-
25
V
RL = 1kΩ, VIN = 2V
26
33
38
V
-
150
-
oC
ICL = -100mA, VCC = 4.5V to 25V, (VCC - 62) (VCC - 37) (VCC - 28) V
VIN = 0.8V
(Note 4)
0.7
1.1
1.7
A
2.0
-
-
V
-
-
0.8
V
VIN = 5.5V, VCC = 6V to 24
10
-
40
µA
VIN = 0.8V, VCC = 6V to 24V
10
-
30
µA
VIN = 2V; IOUT = 0.55A
-
-
0.6
A
Supply Current, No Load,
Input Control OFF
ICCMIN
VIN = 0V; IOUT = 0A
-
55
150
µA
Input-Output Forward Voltage
Drop (VCC - VOUT)
VSAT
IOUT = 0.6A, VCC = 4.5V to 25V
-
-
1.0
V
Output Leakage
Turn-On Time
Turn-OFF Time
IOUT_LK VIN = 0.8V, VCC = 6V to 24V
-
-
50
µA
tON
RL = 80Ω, TA = 125°C
-
6
20
µs
tOFF
RL = 80Ω, TA = 125°C
-
17
65
µs
NOTE:
4. Short Circuit current will be reduced when Thermal Shutdown occurs. Testing of a short circuit current may require a short duration pulse.
2
Share Link: 