LA7265W(1998) Ver la hoja de datos (PDF) - SANYO -> Panasonic
Número de pieza
componentes Descripción
Lista de partido
LA7265W Datasheet PDF : 24 Pages
| |||
Continued from preceding page.
LA7265W
Parameter
Symbol
Conditions
γ.max characteristics 3
γ.max knee characteristics
γ dark clipping characteristics
Y gain control minimum gain
Y gain control maximum gain
Y gain control typical gain
Y gain control D range
γ = 1 DC level
γ = 0.45 frequency characteristics
γ = 1 frequency characteristics
γ = 0.6 frequency characteristics
LSP.SW DC offset
DL.OUT DC level
LSP.SW gain differential
DL.OUT gain
Aperture clipping standard voltage
Aperture clipping level (maximum)
Aperture maximum level
Aperture dark point
Aperture dark slope (typical)
Aperture dark slope (minimum)
Aperture dark slope (maximum)
Aperture Y signal gain
γM3
γMK
γMC
γ2L
γ2H
γ2T
γ2D
γ2DC
γ1F
γ2F
γ3F
LSPDO
LSPDC
LSPGD
LSPG
APCT
APCH
APH
APDP
APDST
APDSL
APDSH
APYG
Measure the output voltage difference for inputs of
0 Vp-p and 500 mVp-p. T5 output
Measure the output voltage difference for inputs of
0 Vp-p and 1500 mVp-p. T5 output
Measure the output voltage difference for inputs of
0 Vp-p and 200 mVp-p. Stipulated as the difference
between that measurement and γM2. T5 output
Measure the output voltage difference for inputs of
0 Vp-p and 200 mVp-p. Stipulated as the gain with
respect to the input. T5 output
Measure the output voltage difference for inputs of
0 Vp-p and 200 mVp-p. Stipulated as the gain with
respect to the input. T5 output
Measure the output voltage difference for inputs of
0 Vp-p and 200 mVp-p. Stipulated as the gain with
respect to the input. T5 output
Measure the output voltage difference for inputs of
0 Vp-p and 1500 mVp-p. T5 output
Measure the output voltage (OPB) with no input.
T5 output
Stipulated as the gain difference between 10 MHz
and f = 500 kHz. T5 output
Stipulated as the gain difference between 10 MHz
and f = 500 kHz. T5 output
Stipulated as the gain difference between 10 MHz
and f = 500 kHz. T5 output
Stipulated as the output voltage difference between
SW14 being set to the B and A positions for a 0 Vp-p
input. T6 output
Measure the output voltage (OPB) with no input.
T6 output
With SW14 in the B position, measure the output voltage
difference for inputs of 0 Vp-p and 500 mVp-p. Perform
the same measurement with SW14 in the A position.
Stipulated as the difference between the two voltage
differences. T6 output
Measure the output voltage difference for inputs of
0 Vp-p and 500 mVp-p. Stipulated as the gain with
respect to the input. T6 output
Input a f = 2 MHz, 200 mVp-p signal and adjust VR1 so
that the output amplitude becomes 44 mVp-p.
Determine the VR9 voltage at that time. T7 output
Measure the output for an f = 2 MHz, 200 mVp-p input
signal. T7 output
Measure the output for an f = 2 MHz, 200 mVp-p input
signal. T7 output
Measure the output amplitude for an f = 2 MHz,
200 mVp-p input signal. Stipulated as the VR4 setting
where the output starts to decrease when VR4 is slowly
increased starting at 0 mV. T7 output
With VR4 set at 0 V and 2.4 V, measure the output
gain for an f = 2 MHz, 200 mVp-p input signal.
Stipulated as the difference between those two gains.
T7 output
With VR4 set at 0 V and 2.4 V, measure the output
gain for an f = 2 MHz, 200 mVp-p input signal.
Stipulated as the difference between those two gains.
T7 output
With VR4 set at 0 V and 2.4 V, measure the output
gain for an f = 2 MHz, 200 mVp-p input signal.
Stipulated as the difference between those two gains.
T7 output
Measure the output voltage difference for inputs of
0 Vp-p and 300 mVp-p. Stipulated as the gain with
respect to the input. T7 output
min
200
520
0
–24
10
0.2
1.10
0.87
–5.0
–2.9
–4.7
–10
2.30
–20
–0.5
2.35
100
1.90
–1.0
Ratings
Unit
typ
max
515
675
mV
750
930
mV
105
280
mV
–16
–8
dB
11
12
dB
1.4
2.3
dB
1.53
V
1.49
2.11
V
–3.8
dB
–1.9
dB
–3.7
dB
0
+10
mV
2.52
2.75
V
0
+20
mV
0
+0.5
dB
2.60
2.85
V
36
mV
320
500
mV
2.06
2.22
V
–1.0
dB
0.5
dB
–4.0
dB
–0.5
0
dB
Continued on next page.
No. 4850-4/24
Share Link: 