MC-4532DA726PFB-A10 Ver la hoja de datos (PDF) - Elpida Memory, Inc

Número de pieza

componentes Descripción

Lista de partido

MC-4532DA726PFB-A10

32 M-WORD BY 72-BIT SYNCHRONOUS DYNAMIC RAM MODULE REGISTERED TYPE

Elpida Memory, Inc 

MC-4532DA726

DC Characteristics (Recommended Operating Conditions unless otherwise noted)

Parameter

Symbol

Test condition

Grade MIN. MAX. Unit Notes

Operating current

ICC1

Precharge standby current in ICC2P

Epower down mode

ICC2PS

Precharge standby current in ICC2N

non power down mode

O ICC2NS

Active standby current in

L power down mode

ICC3P

ICC3PS

Burst length = 1

tRC ≥ tRC (MIN.), IO = 0 mA

/CAS latency = 2

/CAS latency = 3

CKE ≤ VIL (MAX.), tCK = 15 ns

CKE ≤ VIL (MAX.), tCK = ∞

CKE ≥ VIH (MIN.), tCK = 15 ns, /CS ≥ VIH (MIN.),

Input signals are changed one time during 30 ns.

CKE ≥ VIH (MIN.), tCK = ∞ ,

Input signals are stable.

CKE ≤ VIL (MAX.), tCK = 15 ns

CKE ≤ VIL (MAX.), tCK = ∞

-A80

-A10

-A80

-A10

2,100 mA 1

2,100

2,100

2,100

268 mA

98

610 mA

224

340 mA

152

Active standby current in

ICC3N CKE ≥ VIH (MIN.), tCK = 15 ns, /CS ≥ VIH (MIN.),

790 mA

non power down mode

Input signals are changed one time during 30 ns.

ICC3NS CKE ≥ VIH (MIN.), tCK = ∞ ,

440

Input signals are stable.

P Operating current

ICC4 tCK ≥ tCK (MIN.), IO = 0 mA

/CAS latency = 2 -A80

2,190 mA 2

(Burst mode)

-A10

1,830

/CAS latency = 3 -A80

2,640

r -A10

2,280

CBR (Auto) Refresh current

ICC5

tRC ≥ tRC (MIN.)

/CAS latency = 2 -A80

4,440 mA 3

o -A10

4,440

/CAS latency = 3 -A80

4,440

-A10

4,440

d Self refresh current

ICC6 CKE ≤ 0.2 V

286 mA

Input leakage current

II (L) VI = 0 to 3.6 V, All other pins not under test = 0 V

–10 +10 µA

Input leakage current (CKE0)

–20 +20

u Output leakage current

IO (L) DOUT is disabled, VO = 0 to 3.6 V

–1.5 +1.5 µA

High level output voltage

VOH IO = –4.0 mA

2.4

V

Low level output voltage

VOL IO = +4.0 mA

0.4 V

c Notes 1. ICC1 depends on output loading and cycle rates. Specified values are obtained with the output open.

In addition to this, ICC1 is measured on condition that addresses are changed only one time during tCK (MIN.).

t 2. ICC4 depends on output loading and cycle rates. Specified values are obtained with the output open.

In addition to this, ICC4 is measured on condition that addresses are changed only one time during tCK (MIN.).

3. ICC5 is measured on condition that addresses are changed only one time during tCK (MIN.).

6

Data Sheet E0072N10

Share Link: