MCP3905AT-ISS Ver la hoja de datos (PDF) - Microchip Technology

Número de pieza

componentes Descripción

Lista de partido

MCP3905AT-ISS

Energy Metering ICs with Active Real Power Pulse Output

Microchip Technology 

MCP3905A/05L/06A

1.0 ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

VDD ...................................................................................7.0V

Digital inputs and outputs w.r.t. AGND........ -0.6V to VDD +0.6V

Analog input w.r.t. AGND ..................................... ....-6V to +6V

VREF input w.r.t. AGND ............................... -0.6V to VDD +0.6V

Storage temperature .....................................-65°C to +150°C

Ambient temp. with power applied ................-65°C to +125°C

Soldering temperature of leads (10 seconds) ............. +300°C

ESD on the analog inputs (HBM,MM) .................5.0 kV, 500V

ESD on all other pins (HBM,MM) ........................5.0 kV, 500V

† Notice: Stresses above those listed under "Maximum

Ratings" may cause permanent damage to the device. This is

a stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operation listings of this specification is not implied. Exposure

to maximum rating conditions for extended periods may affect

device reliability.

ELECTRICAL CHARACTERISTICS

Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = DVDD = 4.5V – 5.5V,

Internal VREF, HPF turned on (AC mode), AGND, DGND = 0V, MCLK = 3.58 MHz; TA = -40°C to +85°C.

Parameter

Sym

Min Typ.

Max Units

Comment

Overall Measurement Accuracy

Energy Measurement Error

E

—

0.1

— % FOUT Channel 0 swings 1:500 range,

MCP3905A, MCP3905L only

(Note 1, Note 4)

—

0.1

— % FOUT Channel 0 swings 1:1000 range,

MCP3906A only (Note 1, Note 4)

No-Load Threshold/

Minimum Load

NLT

— 0.0015 — % FOUT Disabled when F2, F1, F0 = 0, 1, 1

Max (Note 5, Note 6)

Phase Delay Between

Channels

—

— 1/MCLK s HPF = 0 and 1, < 1 MCLK

(Note 4, Note 6, Note 7)

AC Power Supply Rejection AC PSRR — 0.01

(output frequency variation)

— % FOUT F2, F1, F0 = 0, 1, 1 (Note 3)

DC Power Supply Rejection DC PSRR — 0.01

(output frequency

variation)

— % FOUT HPF = 1, Gain = 1 (Note 3)

System Gain Error

ADC/PGA Specifications

—

3

10 % FOUT (Note 2, Note 5)

Offset Error

VOS

Gain Error Match

Internal Voltage Reference

—

2

—

0.5

5

mV Referred to Input

— % FOUT (Note 5)

Voltage

—

2.4

—

V

Tolerance

—

±2

—

%

Tempco

—

15

— ppm/°C

Note 1: Measurement error = (Energy Measured By Device - True Energy)/True Energy * 100%. Accuracy is

measured with signal (±660 mV) on Channel 1. FOUT0, FOUT1 pulse outputs. Valid from 45 Hz to 65 Hz.

See typical performance curves for higher frequencies and increased dynamic range.

2: Does not include internal VREF. Gain = 1, CH0 = 470 mVDC, CH1 = 660 mVDC, difference between

measured output frequency and expected transfer function.

3: Percent of HFOUT output frequency variation; Includes external VREF = 2.5V, CH1 = 100 mVRMS @

50 Hz, CH2 = 100 mVRMS @ 50 Hz, AVDD = 5V + 1Vpp @ 100 Hz. DC PSRR: 5V ±500 mV

4: Error applies down to 60 degree lead (PF = 0.5 capacitive) and 60 degree lag (PF = 0.5 inductive).

5: Refer to Section 4.0 “Device Overview” for complete description.

6: Specified by characterization, not production tested.

7: 1 MCLK period at 3.58 MHz is equivalent to less than <0.005 degrees at 50 or 60 Hz.

DS22011A-page 2

© 2006 Microchip Technology Inc.

Share Link: