MP2101 Ver la hoja de datos (PDF) - Monolithic Power Systems

Número de pieza

componentes Descripción

Lista de partido

MP2101

1.6MHz Synchronous Step-Down plus 200mA LDO

Monolithic Power Systems 

TM

MP2101 – 1.6MHz SYNCHRONOUS STEP-DOWN PLUS 200mA LDO

ELECTRICAL CHARACTERISTICS (4) (continued)

VIN1/2 = VEN1/2 = 3.6V, TA = +25°C, unless otherwise noted.

Parameters

Condition

Min Typ

SW1 PFET On Resistance

SW1 NFET On Resistance

SW1 Leakage Current

SW1 PFET Peak Current Limit

ISW1 = 100mA

ISW1 = –100mA

VEN1 = 0V, VIN = 6V

VSW1 = 0V or 6V

Duty Cycle = 100%,

Current Pulse Width < 1ms

0.35

0.25

–2

0.9 1.4

Oscillator Frequency

1.2 1.6

Linear Regulator LDO

IN2 Input Range

Regulated FB2 Voltage

ILOAD = 10mA, VOUT2=VFB2

TA = +25°C

–40°C ≤ TA ≤ +85°C

1.2

0.588

0.582

0.600

FB2 Input Bias Current

OUT2 Short Circuit Foldback

OUT2 Output Current

Dropout Voltage (5)

VFB2 = 0.6V

VOUT2 = 0V

VOUT = 1.2V

ILOAD = 150mA, VOUT2 = 1.2V

–50 –2

180

200

280

Notes:

4) Production test at +25°C. Specifications over the temperature range are guaranteed by design and characterization.

5) The dropout voltage is equal to VIN2 – VOUT2 when VOUT2 is 100mV below the nominal value.

Max

+2

2.0

2.0

VIN1

0.612

0.618

+50

Units

Ω

Ω

µA

A

MHz

V

V

nA

mA

mA

mV

PIN FUNCTIONS

Pin # Name Description

1

FB1 Feedback 1. Feedback Input for the switcher output (OUT1).

2

EN1 Enable 1. Enable input for the switcher. Pull high to turn on the switcher; low to turn it off.

3

IN1

Input 1. Main input supply for both the switcher and the auxiliary low dropout (LDO) linear

regulator.

4

SW1 Switcher Switch Node. Output for the 800mA switcher channel.

5

GND Ground.

6

IN2 Input 2. Input supply for the auxiliary linear regulator LDO output power device.

7

OUT2

Output 2. Output of the 200mA LDO. The LDO is designed to be stable with an external

minimum 1µF ceramic capacitor at 200mA of load current.

Power On Reset Open Drain Output. A high output indicates that both outputs are within

±10% of the regulation value. A low output indicates that the output is outside of the ±10%

8 PWROK window. PWROK is pulled down if EN1 and/or EN2 is low. The PWROK window comparators

have a 50µs deglitch timer for the switcher and 150µs deglitch timer for the linear regulator

LDO to avoid a false trigger during load transient.

9

EN2

Enable 2. Enable input for the linear regulator LDO. Pull high to turn on the LDO; low to turn it

off.

10

FB2 Feedback 2. Feedback input for the linear regulator output (OUT2).

MP2101 Rev. 1.0

www.MonolithicPower.com

3

8/18/2006

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.

© 2006 MPS. All Rights Reserved.

Share Link: