MP3011 Ver la hoja de datos (PDF) - Monolithic Power Systems
Número de pieza
componentes Descripción
Lista de partido
MP3011 Datasheet PDF : 8 Pages
| |||
TM
MP3011 – 1X, 1.5X, 2X AUTO-ADJUST CHARGE PUMP 2 WHITE LED DRIVER
PACKAGE REFERENCE
PIN 1 ID
TOP VIEW
LED2 LED1 NC BATT
16 15 14 13
NC 1
12 EN
NC 2
11 RADJ
GND 3
10 GND
C1A 4
9 C2B
5678
BATT C2A C1B LEDC
EXPOSED PAD
CONNECT TO PIN 8
MP3011_PD01_QFN16
Part Number* Package
Temperature
MP3011DQ
QFN16
(3mm x 3mm)
–40°C to +125°C
* For Tape & Reel, add suffix –Z (eg. MP3011DQ–Z)
For Lead Free, add suffix –LF (eg. MP3011DQ–LF–Z)
ABSOLUTE MAXIMUM RATINGS (1)
VBATT to GND .............................................. 6.5V
Power Dissipation..................................... 1.0 W
Logic Inputs to GND ..................... –0.3V to 6.5V
Storage Temperature ...............–65 °C to 150°C
Junction Temperature...............................150°C
Recommended Operating Conditions (2)
Input Voltage VBATT ......................... 2.5V to 5.5V
Operating Temperature (3) .........–40°C to +85°C
Thermal Resistance (4) θJA θJC
QFN16 .................................... 60 ...... 14... °C/W
Notes:
1) Exceeding these ratings may damage the device.
2) The device is not guaranteed to function outside of its
operating conditions.
3) Ambient Operating Temperature.
4) Measured on approximately 1” square of 1 oz copper.
ELECTRICAL CHARACTERISTICS
VBATT = 5V, TA = +25°C, unless otherwise noted.
Parameter
Symbol Condition
Min Typ Max Units
Input Supply Voltage
VBATT
2.5
5.5 V
VBATT at 1x to 1.5x Mode Switch
VBATT 1x-1.5x
ILED = 40mA, VBATT Decreasing,
VLED = 3.75V @ 40mA
3.9
V
VBATT at 1.5x to 2x Mode Switch
VBATT 1.5x-2x
ILED = 40mA, VBATT Decreasing,
VLED = 3.75V @ 40mA
2.9
V
VBATT at 2x to 1.5x Mode Switch
VBATT 2x-1.5x
VBATT Increasing,
VLED = 3.75V @ 40mA
3.1
V
VBATT at 1.5x to 1x Mode Switch
VBATT 1.5x-1x
VBATT Increasing,
VLED = 3.75V @ 40mA
4.1
V
Supply Current
IBATT
2 LEDs at 40mA, 2x Mode,
VBATT = 2.5V
164
mA
Supply Current Shutdown
Current Matching (5)
IBATT SHDN VEN = 0V
ILED MATCH ILED = 40mA
0.1
1
µA
1.5
%
Enable Voltage, High
VEN (HIGH)
1.5
V
Enable Voltage, Low
VEN (LOW)
1.0
V
Enable Pin Leakage
IEN
VEN = 5V
0.1
1
µA
Charge Pump Frequency
Time to Standby Mode (6)
FCP
TOFF
VBATT = 3.3V
Enable Switched Low
1.0 1.3 1.6 MHz
30
µs
Enable Pin PWM Frequency Limit FHPWM
50
KHz
LED Current
ILED
RSET = 1.54kΩ
40
mA
Notes:
5) Matching is defined as the difference of the maximum to minimum current divided by the sum of the maximum and minimum currents.
6) Standby mode switches to shutdown when the output voltage on LEDC drifts back to GND.
MP3011 Rev. 1.1
www.MonolithicPower.com
2
10/31/2005
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
Share Link: 