PI5C16212AE Ver la hoja de datos (PDF) - Pericom Semiconductor
Número de pieza
componentes Descripción
Lista de partido
PI5C16212AE Datasheet PDF : 5 Pages
| |||
PI5C16212
1122334455667788990011223344556677889900112233445566778899001122112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667728899400-11B2233i44t5566B7788u99s0011-22E3344x55c6677h88a9900n1122g11e2233S4455w6677i88t99c00h1122
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .............................................. –65°C to +150°C
Ambient Temperature with Power Applied ..............–40°C to +85°C
Supply Voltage to Ground Potential .......................... –0.5Vto+7.0V
DC Input Voltage ....................................................... –0.5Vto+7.0V
DC Output Current ................................................................ 120mA
Power Dissipation ....................................................................... 1W
Note:
Stresses greater than those listed under MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
Recommended Operating Condition
Parameter
Description
VCC
Supply Voltage
VIH
High-Level Input Voltage
VIL
Low-Level Input Voltage
TA
Operating Free-Air Temperature
Min.
4
2
—
–40
Max.
5.5
—
0.8
85
Units
V
°C
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±10%)
Parameters
Description
Test Conditions(1)
Min.
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
II
Input Current
VCC = Max., VIN = VCC or GND
—
VCC = 0, VIN = VCC
—
IO ZH
High Impedance Output Current 0 - A, B - VCC
—
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18mA
—
IOS
Short Circuit Current(3)
A (B) = 0V, B (A) = VCC
100
VH
Input Hysteresis at Control Pins
—
VCC = Min., VIN = 0.0V,
20
ION = 64mA
RON
Switch On Resistance(4)
VCC = Min., VIN = 2.4V,
—
ION = 15mA
20
Typ(2)
—
—
—
—
—
–0.7
—
150
28
—
35
Max.
—
0.8
±1
10
±1
–1.2
—
—
40
12
48
Units
V
µA
V
mA
mV
Ω
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(5)
Description
Test Conditions
Typ.
Max.
Units
CIN
Input Capacitance
VIN = 0V
3
6
COFF
A/B Capacitance, Switch Off
VIN = 0V
6
14
pF
CON
A/B Capacitance, Switch On
VIN = 0V
12
30
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the
lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
2
PS7023J
09/09/04
Share Link: 