HIP6019 Ver la hoja de datos (PDF) - Intersil

Número de pieza

componentes Descripción

Lista de partido

HIP6019

Advanced Dual PWM and Dual Linear Power Control

Intersil 

HIP6019

settings above, and including 2.5V. This is accomplished by

inverting the triangle wave sent to PWM 2.

Component Selection Guidelines

Output Capacitor Selection

The output capacitors for each output have unique

requirements. In general the output capacitors should be

selected to meet the dynamic regulation requirements.

Additionally, the PWM converters require an output capacitor

to filter the current ripple. The linear regulator is internally

compensated and requires an output capacitor that meets

the stability requirements. The load transient for the

microprocessor core requires high quality capacitors to

supply the high slew rate (di/dt) current demands.

PWM Output Capacitors

Modern microprocessors produce transient load rates above

10A/ns. High frequency capacitors initially supply the transient

and slow the current load rate seen by the bulk capacitors.

The bulk filter capacitor values are generally determined by

the ESR (effective series resistance) and ESL (effective series

inductance) parameters rather than actual capacitance.

High frequency decoupling capacitors should be placed as

close to the power pins of the load as physically possible. Be

careful not to add inductance in the circuit board wiring that

could cancel the usefulness of these low inductance

components. Consult with the manufacturer of the load on

specific decoupling requirements.

Use only specialized low-ESR capacitors intended for

switching regulator applications for the bulk capacitors. The

bulk capacitor’s ESR determines the output ripple voltage and

the initial voltage drop after a high slew-rate transient. An

aluminum electrolytic capacitor’s ESR value is related to the

case size with lower ESR available in larger case sizes.

However, the equivalent series inductance of these capacitors

increases with case size and can reduce the usefulness of the

capacitor to high slew-rate transient loading. Unfortunately,

ESL is not a specified parameter. Work with your capacitor

supplier and measure the capacitor’s impedance with

frequency to select suitable components. In most cases,

multiple electrolytic capacitors of small case size perform

better than a single large case capacitor. For a given transient

load magnitude, the output voltage transient response due to

the output capacitor characteristics can be approximated by

the following equation:

VTRAN = ESL × d----I--T--d--R--t--A----N-- + ESR × ITRAN

Linear Output Capacitors

The output capacitors for the linear regulator and the linear

controller provide dynamic load current. The linear controller

uses dominant pole compensation integrated in the error

amplifier and is insensitive to output capacitor selection.

Capacitor, COUT3 should be selected for transient load

regulation.

The output capacitor for the linear regulator provides loop

stability. The linear regulator (OUT4) requires an output

capacitor characteristic shown in Figure 13 The upper line

plots the 45 phase margin with 150mA load and the lower

line is the 45 phase margin limit with a 10mA load. Select a

COUT4 capacitor with characteristic between the two limits.

0.7

0.6

0.5

0.4

0.3

OSPTEARBALTEION

0.2

0.1

10

100

1000

CAPACITANCE (µF)

FIGURE 13. COUT4 OUTPUT CAPACITOR

Output Inductor Selection

Each PWM converter requires an output inductor. The

output inductor is selected to meet the output voltage ripple

requirements and sets the converter’s response time to a

load transient. The inductor value determines the converter’s

ripple current and the ripple voltage is a function of the ripple

current. The ripple voltage and current are approximated by

the following equations:

∆I = V-----I-F-N---S--–---×-V----L-O--O--U----T-- × V----V-O---I-U-N---T--

∆VOUT = ∆I × ESR

Increasing the value of inductance reduces the ripple current

and voltage. However, the large inductance values reduce

the converter’s response time to a load transient.

One of the parameters limiting the converter’s response to a

load transient is the time required to change the inductor

current. Given a sufficiently fast control loop design, the

HIP6019 will provide either 0% or 100% duty cycle in response

to a load transient. The response time is the time interval

required to slew the inductor current from an initial current value

to the post-transient current level. During this interval the

difference between the inductor current and the transient

current level must be supplied by the output capacitors.

Minimizing the response time can minimize the output

capacitance required.

The response time to a transient is different for the

application of load and the removal of load. The following

2-263

Share Link: