ADL5390-EVALZ(RevA) Ver la hoja de datos (PDF) - Analog Devices
Número de pieza
componentes Descripción
Lista de partido
ADL5390-EVALZ Datasheet PDF : 23 Pages
| |||
Data Sheet
ADL5390
SPECIFICATIONS
VS = 5 V, TA = 25°C, ZO = 50 Ω, FRF = 380 MHz, single-ended source drive to INPI and INPQ, and INMI and INMQ are ac-coupled to
common, unless otherwise noted. 66.5 Ω termination resistors before ac-coupling capacitors on INPI and INPQ. The specifications refer
to one active channel with the other channel input terminated in 50 Ω. The common-mode level for the gain control inputs is 0.5 V. A
maximum gain setpoint of 1.0 refers to a differential gain control voltage of 0.5 V.
Table 1.
Parameter
OVERALL FUNCTION
Frequency Range
Gain Control Range
GAIN CONTROL INTERFACE (I and Q)
Gain Scaling
Modulation Bandwidth
Second Harmonic Distortion
Third Harmonic Distortion
Step Response
FRF = 70 MHz
Maximum Gain
Gain Conformance
Output Noise Floor
Output IP3
Output 1 dB Compression Point
Input 1 dB Compression Point
Gain Flatness
Gain Matching
Phase Matching
Input Impedance
Output Return Loss
FRF = 140 MHz
Maximum Gain
Gain Conformance
Output Noise Floor
Output IP3
Output 1 dB Compression Point
Input 1 dB Compression Point
Gain Flatness
Gain Matching
Phase Matching
Input Impedance
Output Return Loss
FRF = 380 MHz
Maximum Gain
Gain Conformance
Conditions
Min
20
Relative to maximum gain
QBBP, QBBM, IBBM, IBBP (Pins 4, 5, 14, 15)
500 mV p-p, sinusoidal baseband input single-
ended
500 mV p-p, 1 MHz, sinusoidal baseband input
differential
500 mV p-p, 1 MHz, sinusoidal baseband input
differential
For gain from −15 dB to +5 dB
For gain from +5 dB to −15 dB
Maximum gain setpoint
Over gain setpoint of 0.2 to 1.0
Maximum gain setpoint, no RF input
RF PIN = −5 dBm, frequency offset = 20 MHz
FRF1 = 70 MHz, FRF2 = 72.5 MHz, maximum gain
setpoint
Maximum gain setpoint
Gain setpoint = 0.1
Over any 60 MHz bandwidth
At maximum gain setpoint
At maximum gain setpoint
INPI, INMI, INMQ, INMP (Pins 20, 21, 22, 23)
RFOP, RFOM (Pins 9, 10) measured through
balun
Maximum gain setpoint
Over gain setpoint of 0.2 to 1.0
Maximum gain setpoint, no RF input
RF PIN = −5 dBm, frequency offset = 20 MHz
FRF1 = 140 MHz, FRF2 = 142.5 MHz, maximum
gain setpoint
Maximum gain setpoint
Gain setpoint = 0.1
Over any 60 MHz bandwidth
At maximum gain setpoint
At maximum gain setpoint
INPI, INMI, INMQ, INMP (Pins 20, 21, 22, 23)
RFOP, RFOM (Pins 9, 10) measured through
balun
Maximum gain setpoint
Over gain setpoint of 0.2 to 1.0
Typ
35
3.5
230
45
55
45
47
4.6
0.25
−149
−146
23
10.7
6.7
0.25
0.5
±0.25
250||1
9.7
Max Unit
2400 MHz
dB
1/V
MHz
dBc
dBc
ns
ns
dB
dB
dBm/Hz
dBm/Hz
dBm
dBm
dBm
dB
dB
Degrees
Ω||pF
dB
4.5
0.25
−144
−145
24.4
11
7.1
0.25
0.5
±0.25
250||1
9.6
dB
dB
dBm/Hz
dBm/Hz
dBm
dBm
dBm
dB
dB
Degrees
Ω||pF
dB
4.1
dB
0.25
dB
Rev. A | Page 3 of 23
Share Link: 