IH5140CJE Ver la hoja de datos (PDF) - Intersil

Número de pieza

componentes Descripción

Lista de partido

IH5140CJE

High-Level CMOS Analog Switches

Intersil 

IH5140 thru IH5145

Absolute Maximum Ratings

V+ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <36V

V+ to VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V

VD to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V

VD to VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <±22V

VL to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <33V

VL to VIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V

VL to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V

VIN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V

Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA

Thermal Information

Thermal Resistance (Typical)

θJA (oC/W) θJC (oC/W)

CERDIP Package . . . . . . . . . . . . . . . .

80

24

PDIP Package . . . . . . . . . . . . . . . . . . . 100

N/A

Maximum Junction Temperature

CERDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175oC

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150oC

Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC

Operating Conditions

Temperature Ranges

Military . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC

Commercial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Electrical Specifications 25oC, V+ = +15V, V- = -15V, VL = +5V

PER CHANNEL PARAMETER

TEST CONDITIONS

MILITARY

-55oC 25oC 125oC

COMMERCIAL

0oC 25oC 70oC UNITS

LOGIC INPUT

Input Logic Current, IINH

Input Logic Current, IINL

SWITCH

VIN = 2.4V, Note 1

VIN = 0.8V, Note 1

±1

±1

10

−

±10

10

µA

±1

±1

10

−

±10

10

µA

Drain Source On Resistance,

rDS(ON)

Channel to Channel rDS(ON) Match,

∆rDS(ON)

Minimum Analog Signal Handling

Capability, VANALOG

Switch OFF Leakage Current,

ID(OFF)+IS(OFF)

Switch On Leakage Current,

ID(ON)+IS(ON)

Minimum Channel to Channel Cross

Coupling Rejection Ratio, CCRR

IS = -10mA,

VANALOG = -10V to +10V

VD = +10V, VS = -10V

VD = -10V, VS = +10V

VD = VS = -10V to +10V

One Channel Off; Any Other

Channel Switches, See

Performance Characteristics

50

50

75

75

75

100

Ω

- 25 (Typ) -

- 30 (Typ) -

Ω

-

±11

-

-

±10

-

V

(Typ)

(Typ)

-

±0.5

100

-

±5

100

nA

-

±0.5

100

-

±5

100

nA

-

±1

200

-

±2

200

nA

- 54 (Typ) -

- 50 (Typ) -

dB

Switch “ON” Time, tON

Switch “OFF” Time, tOFF

Charge Injection, Q(INJ)

See Switching Time Specifications and Timing Diagrams

See Switching Time Specifications and Timing Diagrams

See Performance

Characteristics

- 10 (Typ) -

- 15 (Typ) -

pC

Minimum Off Isolation Rejection

Ratio, OIRR

f = 1MHz, RL = 100Ω,

CL ≤ 5pF, See Performance

Characteristics

- 54 (Typ) -

- 50 (Typ) -

dB

SUPPLY

+ Power Supply Quiescent Current, I+ V+ = +15V, V- = -15V,

- Power Supply Quiescent Current, I-

+5V Supply Quiescent Current, IL

VL = +5V, See Performance

Characteristics

Ground Supply Quiescent Current,

IGND

NOTES:

1.0

1.0

1.0

1.0

1.0

1.0

1.0

1.0

10

10

10

100

µA

10

10

10

100

µA

10

10

10

100

µA

10

10

10

100

µA

1. Some channels are turned on by high (1) logic inputs and other channels are turned on by low (0) inputs; however 0.8V to 2.4V describes

the minimum range for switching properly. Refer to logic diagrams to find logical value of logic input required to produce ON or OFF state.

2. Typical values are for design aid only, not guaranteed and not subject to production testing.

13-5

Share Link: