MAX756 Ver la hoja de datos (PDF) - Maxim Integrated
Número de pieza
componentes Descripción
Lista de partido
MAX756 Datasheet PDF : 9 Pages
| |||
MAX756/MAX757
3.3V/5V/Adjustable-Output,
Step-Up DC-DC Converters
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (OUT to GND) ....................................-0.3V, +7V
Switch Voltage (LX to GND) ........................................-0.3V, +7V
Auxiliary Pin Voltages (SHDN, LBI, LBO, REF,
3/5, FB to GND) ........................................-0.3V, (VOUT + 0.3V)
Reference Current (IREF) ....................................................2.5mA
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 9.09mW/°C above +70°C) .............727mW
SO (derate 5.88mW/°C above +70°C) ..........................471mW
Operating Temperature Ranges:
MAX75_C_ _ ........................................................0°C to +70°C
MAX75_E_ _......................................................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range............................... -65°to +160°C
Lead Temperature (soldering, 10sec) ........................... +300°C
Stresses beyond those listed under “Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Circuits of Figure 1 and Typical Operating Circuit, VIN = 2.5V, ILOAD = 0mA, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
Output Voltage
Minimum Start-Up Supply Voltage
CONDITIONS
MAX756, 3/5 = 0V, 0mA < ILOAD < 200mA
2V < VIN < 3V MAX756, 3/5 = 3V, 0mA < ILOAD < 300mA
MAX757, VOUT = 5V, 0mA < ILOAD < 200mA
ILOAD = 10mA
Minimum Operating Supply
Voltage (once started)
ILOAD = 20mA
MIN
4.8
3.17
4.8
TYP
5.0
3.30
5.0
1.1
0.7
MAX
5.2
3.43
5.2
1.8
Quiescent Supply Current in
3.3V Mode (Note 1)
ILOAD = 0mA, 3/5 = 3V, LBI = 1.25V, VOUT = 3.47V,
FB = 1.3V (MAX757 only)
60
UNITS
V
V
V
µA
Battery Quiescent Current
Measured at VIN in Figure 1
Output set for 3.3V
Shutdown Quiescent Current
(Note 1)
SHDN = 0V, LBI = 1.25V, 3/5 = 3V, VOUT = 3.47V,
FB = 1.3V (MAX757 only)
Reference Voltage
Reference-Voltage Regulation
LBI Input Threshold
No REF load, CREF = 0.1µF
3/5 = 3V, -20µA < REF load < 250µA, CREF = 0.22µF
With falling edge
LBI Input Hysteresis
LBO Output Voltage Low
LBO Output Leakage Current
ISINK = 2mA
LBO = 5V
SHDN, 3/5 Input Voltage Low
SHDN, 3/5 Input Voltage High
SHDN, 3/5, FB, LBI Input Current
LBI = 1.25V, FB = 1.25V, SHDN = 0V or 3V,
3/5 = 0V or 3V
FB Voltage
MAX757
Output Voltage Range
MAX757, ILOAD = 0mA (Note 2)
60
µA
20
40
µA
1.23 1.25 1.27
V
0.8
2.0
%
1.22 1.25 1.28
V
25
mV
0.4
V
1
µA
0.4
V
1.6
V
±100 nA
1.22 1.25 1.28
V
2.7
5.5
V
Note 1: Supply current from the 3.3V output is measured with an ammeter between the 3.3V output and OUT pin. This current
correlates directly with actual battery supply current, but is reduced in value according to the step-up ratio and efficiency.
Note 2: Minimum value is production tested. Maximum value is guaranteed by design and is not production tested.
2
Maxim Integrated
Share Link: 