TEM03 Ver la hoja de datos (PDF) - Unspecified
Número de pieza
componentes Descripción
Lista de partido
TEM03 Datasheet PDF : 2 Pages
| |||
Model
Number
Input
Range
Output
Voltage
Output
Output Input
Voltage Range Current Current (6)
Eff (7)
(%)
Capacitor(8)
Load max
TEM03-05S33
TEM03-05S05
TEM03-05S12
TEM03-05D12
TEM03-12S33
4.5 – 9 VDC
4.5 – 9 VDC
4.5 – 9 VDC
4.5 – 9 VDC
9 – 18 VDC
3.3 VDC
5 VDC
12 VDC
I12 VDC
3.3 VDC
2.84 – 3.67 VDC
4.3 – 6 VDC
12 – 15 VDC
I12 – I15 VDC
2.84 – 3.67 VDC
600 mA
600 mA
250 mA
I125 mA
600 mA
656 mA
909 mA
883 mA
883 mA
253 mA
65
3300 uF
70
1500 uF
72
700 uF
72
I250 uF
70
3300 uF
TEM03-12S05
TEM03-12S12
TEM03-12D12
TEM03-24S33
9 – 18 VDC
9 – 18 VDC
9 – 18 VDC
18 – 36 VDC
5 VDC
12 VDC
I12 VDC
3.3 VDC
4.3 – 6 VDC
12 – 15 VDC
I12 – I15 VDC
2.84 – 3.67 VDC
600 mA
250 mA
I125 mA
600 mA
352 mA
343 mA
343 mA
126 mA
75
1500 uF
77
700 uF
77
I250 uF
70
3300 uF
TEM03-24S05
TEM03-24S12
TEM03-24D12
TEM03-48S33
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
36 – 75 VDC
5 VDC
12 VDC
I12 VDC
3.3 VDC
4.3 – 6 VDC
12 – 15 VDC
I12 – I15 VDC
2.84 – 3.67 VDC
600 mA
250 mA
I125 mA
600 mA
176 mA
169 mA
169 mA
63 mA
75
1500 uF
78
700 uF
78
I250 uF
70
3300 uF
TEM03-48S05
TEM03-48S12
TEM03-48D12
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
5 VDC
12 VDC
I12 VDC
4.3 – 6 VDC
12 – 15 VDC
I12 – I15 VDC
600 mA
250 mA
I125 mA
88 mA
85 mA
85 mA
75
1500 uF
78
700 uF
78
I250 uF
Note
1. The follow output voltage can be outputted by connecting this terminal to an output + or – terminal. Unless the output voltage is adjusted, this terminal
should be open.
2. In addition, the voltage can be adjusted not by shorting these terminals, but by connecting them to resistances as shown below.
3. Arithmetic expression connected resistance: R ( K )
3-1 Vo=(3.3*R+36.7)/(R+10)
3-3 Vo=2.5*[2+2.7/(R+6.8)]
3-2 Vo=(3.3*R+36.7)/(R+12.92)
3-4 Vo=2.5*[2-2.7/(R+9.5)]
PIN CONNECTION
3-5 Vo=2.5+9.5(R+10.9)/(R+8.2) 3-6 Vo=2.5+22*(R+12.7)/(R+10)(Between two outputs)
PIN
SINGLE
DUAL
4. Bellcore TR-NWT-000332. Case1:50% Stress, temperature at 40ºC.
(Ground fixed and controlled environment)
5. The filter capacitor recommended use “ CHEMICON “ KMF series
or equivalent impedance at 0.16 ~ 0.33 ( 100KHz 20 )
6. Maximum value at nominal input voltage and full load.
7. Typical value at nominal input voltage and full load.
8. Test by minimum Vin and constant resistor load.
1
+ Vi
2
- Vi
3
NC
4
- Vo
5
Vset
6
+ Vo
+ Vi
- Vi
- Vo
COM
Vset
+ Vo
Derating Curve
BOTTOM
VIEW
100
75
50
Nature convection
25
0
-20 -10 0 30 40 50 60 70 80
AMBIENT TEMPERATURE (ºC)
ALL DIMENSIONS IN INCHES (mm)
PIN PITCH TOLERANCE I0.014(0.35)
EXTERNAL OUTPUT TRIMMING
Output can be externally trimmed by
using the method shown below.
( ) for dual output trim
TRIM UP
TRIM DOWN
4(3)
5(5)
RU
RD
5(5)
6(6)
Share Link: 