3560 Ver la hoja de datos (PDF) - Unspecified
Número de pieza
componentes Descripción
Lista de partido
3560 Datasheet PDF : 4 Pages
| |||
3
■ Specifications
Measurement method: Resistance AC (1kHz ± 0.2Hz) 4-terminal method
A/D method:
∑-∆ method with sample hold function
Display:
Fluorescent character display tube.
Auto-ranging:
Resistance [31000], voltage [50000] counter
Provided (disabled when comparator is ON)
Input overrange:
" OF " display
Measurement irregularity: " ---- " display (NG: External output of measurement irregularity signal)
Sampling rate:
[FAST]
[MEDIUM]
[SLOW]
50 Hz
50 times/s
6.25 times/s
1.56 times/s
60 Hz
60 times/s
7.52 times/s
1.88 times/s
Response time:
Comparator:
[FAST]
[MEDIUM]
[SLOW]
50 Hz
100 ms
800 ms
1.92 s
60 Hz
84 ms
667 ms
1.60 s
(When non-conductive resistance is measured. The response time
differs depending on the measured object.)
Comparator output (Resistance/voltage measurement mode)
Resistance
Voltage
Hi
IN
Lo
Hi
FAIL (red)
FAIL (red)
FAIL (red)
IN
FAIL (red)
PASS (green)
FAIL (red)
Lo
FAIL (red)
(FAIL) (red)
FAIL (red)
• Mode switch:
• Comparator points:
* Restricted to Hi, IN, Lo in the resistance measurement mode.
Switchable between AUTO and MANU.
Up to 30 comparator condition settings can be memorized.
• Buzzer output:
[Resistance measurement mode]: Switchable between Hi, Lo and IN.
(ON/OFF setting possible) [Resistance/voltage measurement mode]: Switchable between PASS and FAIL.
Maximum input voltage: DC 60 V max. (AC input is not possible)
Withstand voltage:
Between power supply line and protective ground terminal /
AC 2.3 kV rms for 1 minute
External output terminals: [Open-collector output] (DC 35V-50mA max.)
comparator results, measurement termination, measurement
irregularity signal
External control terminal: [CMOS input] Measurement trigger, comparator trigger,
printer, zero-adjustment, comparator number selection,
external power supply possible (DC 5 V to 24 V)
Interfaces:
RS-232C (standard), GP-IB or printer interface [Centronics]
(option)
Environment conditions: Operating temperature and humidity range: 0 to 40˚C (32˚F
to 104˚F) , 80% RH or less.
(no condensation)
Storage temperature and humidity range: -10 to 50˚C (14˚F
to 122˚F) , 80% RH or less.
Operating conditions: Indoors, below an altitude of 2000 m.
Power supply:
AC 100V to 240V (±10%), automatic voltage selection, 50/60Hz
Maximum rated power: 30 VA
Dimensions and mass: 215(W) × 80(H) × 320(D)mm, 2.1kg / [8.5"(W) × 3.1"(H) ×
12.6"(D), 74.1 oz.] (not including options)
Included accessory: 9287-10 CLIP TYPE LEADS (1)
Conforming standards: EMC
Safety
EN61326:1997+A1:1998+A2:2001
EN61000-3-2:2000
EN61000-3-3:1995+A1:2001
EN61010-1:2001
Pollution degree: level 2
■ Measurement Ranges Conditions for guaranteed accuracy: at 23˚C±5˚C[73.4˚F ±9˚F], 80% RH (no condensation), following 30 min.
warming-up, and after zero adjustment
[Resistance measurement] (Sampling speed : SLOW)
[Voltage measurement] (Sampling speed : SLOW)
Range
Maximum
display value
30mΩ
31.000mΩ
300mΩ
310.00mΩ
3Ω
3.1000Ω
30Ω
31.000Ω
300Ω
310.00Ω
3kΩ
3.1000kΩ
Resolution
Measurement
current
1µΩ
7.4mA
10µΩ
1mA
100µΩ
100µA
1mΩ
10µA
10mΩ
5µA
100mΩ
1.5µA
±0.5%rdg.±8dgt.
Accuracy * In the case of MEDIUM: Add 3 dgt. to the above dgt. error
FAST: ±0.5% rdg. ±8 dgt. (30 mΩ)/±0.5% rdg. ±6 dgt. (other ranges)
However, in the case of FAST, the display counter decreases 4 digits in all ranges.
Temperature
modules
(±0.05% rdg. ±0.8 dgt.)/˚C (1.8˚F) *FAST: 300m to 3kΩ range (±0.05% rdg. ± 0.6 dgt.)/˚C (1.8˚F)
Open-terminal
voltage
20 mV peak max. (when limiter is ON)
Range
Maximum
display
DC 5V
±5.0000V
DC 50V
±50.000V
Resolution
100µV
1mV
Accuracy
Temperature
modules
±0.05%rdg. ±5dgt. ±0.05%rdg. ±5dgt.
(±0.005% rdg. ±0.5 dgt.)/˚C (1.8˚F)
* MEDIUM: Add 3 dgt. to the accuracy dgt. error
FAST: Add 5 dgt. to the accuracy dgt. error
* During charging, the measurement value may be unsteady due to
ripple voltage.
* Resistance with inductance elements may not always be
measurable.
3560 AC mΩ HiTESTER
● Options
9452 CLIP TYPE LEADS
9453 FOUR TERMINAL LEADS
9454 ZERO ADJUSTMENT BOARD (for 9461,9465)
9455 PIN TYPE LEADS (for high-density use)
9461 PIN TYPE LEADS
9465 PIN TYPE LEADS
9466 REMOTE CONTROL SWITCH
9467 LARGE CLIP TYPE LEADS
9770 PIN TYPE LEADS
9771 PIN TYPE LEADS
* 9588 GP-IB INTERFACE
* Non CE mark.
9151-02 GP-IB CONNECTION CABLE (2 meters)
9151-04 GP-IB CONNECTION CABLE (4 meters)
9589 PRINTER INTERFACE
9203 DIGITAL PRINTER
9425 CONNECTION CORD (20-pin half-pitch—36pin/D-sub)
[for connecting the 3560 to the 9203/2meters]
9233 RECORDING PAPER (for the 9203/10meters,10rolls)
9287-10 (included)
9452
Approx. 85 cm
between connectors,
and 8 cm between
probes
9461
Approx. 80 cm
between connectors,
and 20 cm between
probes
9465 & 9466
9453
Approx. 80 cm
between connectors,
and 30 cm between
probes
9467
9455
same appearance
as 9461
0.8 dia.
Tip
magnified
view
Current side
Voltage side
0.2/0.2 dia.
Approx. 40 cm
between connectors,
and 25 cm between
probes
9454
Approx. 40 cm
between connectors,
and 25 cm between
probes
9770/9771
For zero-adjustment
when 9461 or 9465 is
used.
Cable length :
connectors to lead
branch approx. 1.7m,
lead branch to probes
approx. 10 cm
9770 -- in detail
Approx. 85 cm between
connectors, and 25 cm
between probes, 29 mm
dia.
9771 -- in detail
Cable length:
connector to fork
40cm, fork to probes
25cm
0.6 mm dia.
1.8 mm dia.
0.2 mm
2.2 mm
DISTRIBUTED BY
HEAD OFFICE :
81 Koizumi, Ueda, Nagano, 386-1192, Japan
TEL +81-268-28-0562 / FAX +81-268-28-0568
E-mail: os-com@hioki.co.jp
HIOKI USA CORPORATION :
6 Corporate Drive, Cranbury, NJ 08512 USA
TEL +1-609-409-9109 / FAX +1-609-409-9108
E-mail: hioki@hiokiusa.com
Shanghai Representative Office :
1310 Shanghai Times Square Office
93 Huaihai Zhong Road
Shanghai, 200021, P.R.China
TEL +86-21-6391-0090, 0092
FAX +86-21-6391-0360
E-mail: info@hioki.cn
All information correct as of Mar. 3, 2006. All specifications are subject to change without notice.
3560E3-63B-03K Printed in Japan
Share Link: 