MP1530 Ver la hoja de datos (PDF) - MPS Industries, Inc.

Número de pieza

componentes Descripción

Lista de partido

MP1530

Triple Output Step-Up Plus Linear Regulators for TFT Bias

MPS Industries, Inc. 

MP1530 – TRIPLE OUTPUT STEP-UP PLUS LINEAR REGULATORS FOR TFT BIAS

PIN FUNCTIONS

QFN

Pin #

1

2

TSSOP

Pin #

15

16

Name Description

Step-Up Converter Power Switch Node. Connect an inductor between the input source

SW and SW, and connect a rectifier from SW to the main output to complete the step-up

converter. SW is the drain of the internal 250mΩ N-Channel MOSFET switch.

Timing Capacitor for Power Supply Soft-Start and Power-On Sequencing. A capacitor

CT from CT to GND controls the soft-start and sequencing turn-on delay periods. See

Power-On Sequencing and Start Up Timing Diagram.

Regulators Not Ready. During startup RDY will be left high. Once the turn-on sequence

is complete, this pin will be pulled low if all FB voltages exceed 80% of their specified

3

1

thresholds. After all regulators are turned-on, a fault in any regulator that causes the

RDY respective FB voltage to fall below 80% of its threshold will cause RDY to go high after

approximately 15μs. If the fault persists for more than approximately 6ms (for CCT=10nF),

the entire chip will shut down. See Fault Sensing and Timer.

Step-Up Converter Feedback Input. FB1 is the inverting input of the internal error

4

2

FB1 amplifier. Connect a resistive voltage divider from the output of the step-up converter to

FB1 to set the step-up converter output voltage.

Step-Up Converter Compensation Node. COMP is the output of the error amplifier.

5

3 COMP Connect a series RC network to compensate the regulation control loop of the step-up

converter.

6

4

IN

Internal Power Input. IN supplies the power to the MP1530. Bypass IN to PGND with a

10μF or greater capacitor.

7

5

GND Signal Ground.

Reference Output. REF is the 1.25V reference voltage output. Bypass REF to GND with

8

6

REF a 0.1μF or greater capacitor. Connect REF to the low-side resistor of the negative linear

regulator feedback string.

Negative Linear Regulator Feedback Input. Connect the FB2 feedback resistor string

9

7

FB2 between GL and REF to set the negative linear regulator output voltage. FB2 regulation

threshold is GND.

Positive Linear Regulator Feedback Input. Connect the FB3 feedback resistor string

10

8

FB3 between GH and GND to set the positive linear regulator output voltage. FB3 regulation

threshold is 1.25V.

On/Off Control Input. Drive EN high to turn on the MP1530, drive EN low to turn it off. For

11

9

EN

automatic startup, connect EN to IN. Once the MP1530 is turned on, it sequences the

outputs on (See Power-On Sequencing). When turned off, all outputs are immediately

disabled.

Negative Linear Regulator Output. GL is the output of the negative linear regulator. GL

12

10

GL can supply up to 20mA to the load. Bypass GL to GND with a 1μF or greater, low-ESR,

ceramic capacitor.

Negative Linear Regulator Input. IN2 is the input of the negative linear regulator. Drive

13

11

IN2 IN2 with an inverting charge pump powered from SW. IN2 can go as low as -20V. For

QFN package, connect the exposed pad to IN2 pin.

MP1530 Rev. 1.41

www.MonolithicPower.com

6

5/25/2011

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.

© 2011 MPS. All Rights Reserved.

Share Link: