HFA1109 Ver la hoja de datos (PDF) - Renesas Electronics
Número de pieza
componentes Descripción
Lista de partido
HFA1109 Datasheet PDF : 12 Pages
| |||
HFA1109
Absolute Maximum Ratings
Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8V
Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected
30mA Continuous
60mA 50% Duty Cycle
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . .1400V
Charged Device Model (Per EOS/ESD DS5.3, 4/14/93) . . . .2000V
Machine Model (Per EIAJ ED-4701Method C-111) . . . . . . . . . .50V
Thermal Information
Thermal Resistance (Typical, Note 3)
JA (°C/W)
8 Lead SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
170
Maximum Junction Temperature (Die). . . . . . . . . . . . . . . . . . +175°C
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
4. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output
current must not exceed 30mA for maximum reliability.
Electrical Specifications
PARAMETER
VSUPPLY = 5V, AV = +2, RF = 250, RL = 100, Unless Otherwise Specified.
TEST CONDITIONS
(NOTE 5)
TEST
LEVEL TEMP. (°C) MIN TYP
INPUT CHARACTERISTICS
Input Offset Voltage
A
25
-
1
A
Full
-
2
Average Input Offset Voltage Drift
B
Full
-
10
Input Offset Voltage
Common-Mode Rejection Ratio
DVCM = ±2V
A
25
47
50
A
Full
45
48
Input Offset Voltage
Power Supply Rejection Ratio
DVPS = ±1.25V
A
25
50
53
A
Full
47
51
Non-Inverting Input Bias Current
A
25
-
4
A
Full
-
5
Non-Inverting Input Bias Current Drift
B
Full
-
30
Non-Inverting Input Bias Current
Power Supply Sensitivity
DVPS = ±1.25V
A
25
-
0.5
A
Full
-
0.5
Inverting Input Bias Current
A
25
-
2
A
Full
-
3
Inverting Input Bias Current Drift
B
Full
-
40
Inverting Input Bias Current
Common-Mode Sensitivity
DVCM = ±2V
A
25
-
3
A
Full
-
3
Inverting Input Bias Current
Power Supply Sensitivity
DVPS = ±1.25V
A
25
-
1.6
A
Full
-
1.6
Non-Inverting Input Resistance
DVCM = ±2V
A
25, 85
0.8
1.7
A
-40
0.5
1.4
Inverting Input Resistance
B
25
-
60
MAX
5
8
-
-
-
-
-
10
15
-
1
3
10
15
-
6
8
5
8
-
-
-
UNITS
mV
mV
V/°C
dB
dB
dB
dB
A
A
nA/°C
A/V
A/V
A
A
nA/°C
A/V
A/V
A/V
A/V
M
M
FN4019 Rev.5.00
April 23, 2007
Page 2 of 12
Share Link: 