CS5501-BSZ Ver la hoja de datos (PDF) - Cirrus Logic

Número de pieza

componentes Descripción

Lista de partido

CS5501-BSZ

Non-aliasing, 16- & 20-bit A/D Converters

Cirrus Logic 

CS5501 CS5503

CS5501/CS5503

Cal Mode

Self-Cal

System Cal

Zero Scale

AGND

SOFF

Gain Factor

Unipolar

1LSB

Bipolar

CS5501

CS5503

CS5501

CS5503

VREF

VREF

65,536

VREF

1,048,526

2VREF

65,536

2VREF

1,048,526

SGAIN

SGAIN−SOFF

65,536

SGAIN−SOFF

1,048,526

2(SGAIN−SOFF) 2(SGAIN−SOFF)

65,536

1,048,526

Table 3. Output Code Size After Calibration

Input Voltage, Unipolar Mode

Input Voltage, Bipolar Mode

System-Cal

Self-Cal

Output Codes (Hex)

CS5501 CS5503

Self-Cal

System Cal

>(SGAIN - 1.5 LSB) >(VREF - 1.5 LSB) FFFF

FFFFF >(VREF - 1.5 LSB)

>(SGAIN - 1.5 LSB)

SGAIN - 1.5 LSB

VREF - 1.5 LSB

FFFF

FFFE

FFFFF

FFFFE

VREF - 1.5 LSB

SGAIN - 1.5 LSB

(SGAIN - SOFF)/2 - 0.5 LSB VREF/2 - 0.5 LSB

8000

7FFF

80000

7FFFF

AGND - 0.5 LSB

SOFF -0.5 LSB

SOFF + 0.5 LSB

AGND + 0.5 LSB

0001

0000

00001

00000

-VREF+ 0.5 LSB -SGAIN + 2SOFF + 0.5 LSB

<(SOFF + 0.5 LSB) <(AGND+0.5 LSB) 0000

00000 <(-VREF+0.5 LSB) <(-SGAIN+2SOFF+0.5 LSB)

Table 4. Output Coding

Tables 3 and 4 indicate the output code size and

output coding of the CS5501/CS5503 in its vari-

ous modes. The calibration equations which

represent the CS5501/CS5503 transfer function

are shown in Figure 10.

DOUT = Slope (AIN - Unipolar Offset) + 0.5 LSB

a. Unipolar Calibration

Underrange And Overrange Considerations

The input signal range of the CS5501/CS5503

will be determined by the mode in which the part

is calibrated. Table 4 indicates the input signal

range in the various modes of operation. If the

input signal exceeds the full scale point the con-

verter will output all ones. If the signal is less

than the zero scale point (in unipolar) or more

negative in magnitude than minus the full scale

point (in bipolar) it will output all zeroes.

CS5501

DOUT = Slope (AIN - Bipolar Offset) + 215 + 0.5 LSB16

CS5503

DOUT = Slope(AIN - Bipolar Offset) + 219 + 0.5 LSB20

b. Bipolar Calibration

Note that the modulator-filter combination in the

chip CS5501/CS5503 is designed to accurately

convert and filter input signals with noise excur-

sions which extend up to 100 mV below the

analog value which produces all zeros out or

above the analog value which produces all ones

out. Overrange noise excursions greater than

100 mV may increase output noise.

Figure 10. Calibration Equations

2200

All pins of the CS5501/CS5503 include diodes

which clamp the input signals to within the posi-

tive and negative supplies. If a signal on any pin

(including AIN) exceeds the supply voltage (either

DS31F54

Share Link: