AC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 5%, TA = 0 to + 70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ns
Output Timing Reference Level . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 V
Output Load . . . . . . . . . . . . See Figure 1A Unless Otherwise Noted
READ/WRITE CYCLE TIMING (See Notes 1, 2, 3, and 4)
MCM67H618A–9 MCM67H618A–10 MCM67H618A–12
Parameter
Symbol
Min
Max
Min
Max
Min
Max
Unit Notes
Cycle Time
tKHKH
15
—
16.6
—
20
—
ns
Clock Access Time
tKHQV
—
9
—
10
—
12
ns
5
Output Enable to Output Valid
tGLQV
—
5
—
5
—
6
ns
Clock High to Output Active
tKHQX1
6
—
6
—
6
—
ns
Clock High to Output Change
tKHQX2
3
—
3
—
3
—
ns
Output Enable to Output Active
tGLQX
0
—
0
—
0
—
ns
Output Disable to Q High–Z
tGHQZ
—
6
—
7
—
7
ns
6
Clock High to Q High–Z
tKHQZ
3
6
3
7
3
7
ns
Clock High Pulse Width
tKHKL
5
—
5
—
6
—
ns
Clock Low Pulse Width
tKLKH
5
—
5
—
6
—
ns
Setup Times:
Address tAVKH
2.5
—
2.5
—
2.5
—
ns
7
Address Status tADSVKH
Data In tDVKH
Write tWVKH
Address Advance tADVVKH
Chip Enable tEVKH
Hold Times:
Address tKHAX
0.5
—
0.5
—
0.5
—
ns
7
Address Status tKHADSX
Data In tKHDX
Write tKHWX
Address Advance tKHADVX
Chip Enable tKHEX
NOTES:
1. In setup and hold times, W (write) refers to either one or both byte write enables LW and UW.
2. A read cycle is defined by UW and LW high or ADSP low for the setup and hold times. A write cycle is defined by LW or UW low and ADSP
high for the setup and hold times.
3. All read and write cycle timings are referenced from K or G.
4. G is a don’t care when UW or LW is sampled low.
5. Maximum access times are guaranteed for all possible i486 and Pentium external bus cycles.
6. Transition is measured ± 500 mV from steady–state voltage with load of Figure 1B. This parameter is sampled rather than 100% tested.
At any given voltage and temperature, tKHQZ max is less than tKHQZ1 min for a given device and from device to device.
7. This is a synchronous device. All addresses must meet the specified setup and hold times for ALL rising edges of K whenever ADSP or
ADSC is low, and the chip is selected. All other synchronous inputs must meet the specified setup and hold times for ALL rising edges of
K when the chip is enabled. Chip enable must be asserted at each rising edge of clock for the device (when ADSC is low) to remain enabled.
OUTPUT
Z0 = 50 Ω
AC TEST LOADS
RL = 50 Ω
OUTPUT
255 Ω
+5V
480 Ω
5 pF
VL = 1.5 V
Figure 1A
Figure 1B
MOTOROLA FAST SRAM
MCM67H618A
5