3535 Ver la hoja de datos (PDF) - ASM GmbH

Número de pieza

componentes Descripción

Lista de partido

3535

LCR HiTESTER

ASM GmbH 

5

High Speed Testing of Chip Inductors and

Magnetic Heads in Research and Development

3535 Specifications

Measurement

Items

: Z (impedance), Y (admittance), Rs (series-

equivalent resistance, ESR), Rp (parallel-

equivalent resistance), G (conductivity), X

(reactance), B (susceptance), θ (phase angle),

Ls (series-equivalent inductance), Lp (parallel-

equivalent inductance), Cs (series-equivalent

capacitance), Cp (parallel-equivalent capacitance),

Q (Q factor), D (loss constant tanδ)

Measurement

Frequency

: Frequency Range: 100 kHz to 120 MHz

Setting Resolution: Four digits (by front panel setting)*

100.0 kHz to 1.000 MHz: 100-Hz steps

1.000 MHz to 10.00 MHz: 1-kHz steps

10.00 MHz to 100.0 MHz: 10-kHz steps

100.0 MHz to 120.0 MHz: 100-kHz steps

*1-Hz resolution with GP-IB or RS-232C interface

Frequency Accuracy: less than ±0.005% of

setting value

Output Impedance : 50 ±10 Ω (at 100 kHz)

Measurement

Signal Level

: Open-terminal voltage (V) mode

Level Range:

5 mV to 1 V, 20 mA max. (up to 10.00 MHz)

5 mV to 500 mV, 10 mA max. (above 10.01 MHz)

Setting Resolution: 1mV steps

Setting Accuracy: ±(5% + 5 mV) × (2 + log f)

where f is in MHz

Constant Current (CC) mode

Level Range:

200 µA to 20 mA: 1 V max. (up to 10.00 MHz)

200 µA to 10 mA: 0.5 V max. (above 10.01 MHz)

Setting Resolution: 10 µA steps

Setting Accuracy: ±(10% + 50 µA) × (2 + log f)

where f is in MHz

Monitor Function : Monitor Voltage: 0.000 to 1.000 V

Monitor Current: 0.000 to 20.00 mA

Limit Function : Current Limit (during V setting): 0.20 to 20.00 mA

Voltage Limit (during CC setting): 0.005 to 1.000 V

Measurement

Time

: 6 ± 1 ms (nominal)

Actual time depends on measurement conditions,

such as measurement speed and averaging.

Measurement

Speed

: FAST, NORMAL, SLOW and SLOW2

Average

: OFF, 2, 4, 8, 16, 32 and 64

Trigger Function : Internal and external trigger sources can be selected.

Trigger Delay function:

0.01 to 9.99 s with 0.01 s resolution

Load Compensation : Measure a standard component to establish

Function

a compensation value for subsequent

measurements.

Key Lock

Function

: Temporarily disable touch panel operation

using rear panel switch.

Comparator

: Compares two measurement items.

Input either the absolute value, percentage of

standard value or its deviation percentage (Δ%).

Note: for Δ%, the measurement value is

displayed as the percentage of deviation

from the standard value.

Classification (BIN) : Ranks two measurement items into ten

Measurement

classifications.

Correlation

: Constants a and b are entered to compensate

Compensation Function displayed values.

[Compensated value] = a × [measurement value] + b

Panel Save and

Load

: Memory Capacity: 30 Sets

Load Method: Front panel key operation,

External I/O connector, GP-IB, RS-232C

Measurement Value : Memory Capacity: Up to 200 values

Storage

Measurement values are stored in the main unit

and transferred as a batch.

Zoom Display

Function

: Enlarge the display of measurement data and

comparator results.

Continuous

Measurements

: Measurements are made continuously per

conditions saved on the screen.

Audible Beeper

: Beeping can be set ON/OFF for key entry and

comparator results (IN or NG).

Numerical Display

Digit Setting

Function

: Measurement values can be set to display as 3,

4 or 5 digits.

Available settings depend on the parameter.

Display Setting

Functions

: Backlight and voltage/current monitor display

can be set ON/OFF.

Note: when the backlight is off, display refresh

is disabled (during high-speed measurement).

Printer Functions

: Hard copy printout of measurement values and

screens.

Note: requires 9442 and 9444

Interfaces

: GP-IB, RS-232C and EXT I/O (standard)

Operating

Temperature and

Humidity

: 10 to 40°C, 80% rh or less, no condensation

Storage

Temperature and

Humidity

: -10 to 55°C, 80% rh or less, no condensation

Operating

Environment

: Indoors, up to 2000 m ASL

Power

: 100 to 240 VAC, 50/60 Hz

Maximum Rated : 50 VA

Power

Dimensions and Mass : Approx. 360W × 130H × 360D mm, 8.3 kg

Conforming

Standards

: EMC: EN61326:1997+A1:1998+A2:2001

EN61000-3-2:2000

EN61000-3-3:1995+A1:2001

Safety: EN61010-1:2001

Pollution Degree 2

Share Link: