66012 Ver la hoja de datos (PDF) - Micropac Industries
Número de pieza
componentes Descripción
Lista de partido
66012 Datasheet PDF : 2 Pages
| |||
66012
FOUR CHANNEL, HERMETICALLY SEALED, LOW-INPUT CURRENT, 6N140 OPTOCOUPLER
ELECTRICAL CHARACTERISTICS
Ta = -55°C to 125°C unless otherwise specified.
PARAMETER
SYMBOL MIN
TYP
MAX UNITS
TEST CONDITIONS
NOTE
Current Transfer Ratio
CTR
Logic Low Output Voltage
Logic High Output Current
High Level Output Current
Low Level Supply Current
Input Forward Voltage
Input Reverse Breakdown Voltage
Input-Output Insulation Leakage
Current
VOL
IOH
ICCH
ICCL
VF
BVR
II—O
300
1000
300
750
200
400
0.1
0.4
0.2
0.4
.005
250
.010
40
2
4
1.4
1.8
5
1.0
%
IF = 0.5mA, VO = 0.4V, VCC = 4.5V
1,2
%
IF = 1.6mA, VO = 0.4V, VCC = 4.5V
1,2
%
IF = 5.0mA, VO = 0.4V, VCC = 4.5V
1,2
V
IF = 0.5mA, IOL = 1.5mA, VCC = 4.5V
1
V
IF = 5.0mA, IOL = 10mA, VCC = 4.5V
µA
IF = 2µA, VO = VCC = 18V
1,3
µA
IF1 =IF2 =IF3 =IF4 = 0mA, VCC = 18V
mA
IF1= IF2 = IF3 = IF4=1.6mA, VCC = 18V
V
IF = 1.6mA
1
V
IR = 10µA
1
µA
VI—0 = 1500Vdc,
4
Relative Humidity = 45%
Propagation Delay Time To High
tPLH
5
Output Level
4
Propagation Delay Time To Low
tPHL
8
Output Level
2
TYPICAL CHARACTERISTICS Ta = 25°C, VCC = 5V Each Channel
PARAMETER
SYMBOL MIN TYP
60
30
100
10
MAX
tA = 25°C, t = 5s
µs
IF = 0.5mA, VCC = 5.0V, RL = 4.7kΩ
µs
IF = 5mA, VCC = 5.0V, RL = 680kΩ
µs
IF = 0.5mA, VCC = 5.0V, RL = 4.7kΩ
µs
IF = 5mA, VCC = 5.0V, RL = 680kΩ
UNITS
TEST CONDITIONS
NOTE
Input Capacitance
Capacitance (Input-Output)
Input Diode Temperature
Coefficient
Resistance (Input-Output)
Resistance (Input-Input)
Input-Input Insulation Leakage
Current
Common Mode Transient immunity
at High Output Level
Common Mode Transient Immunity
at Low Output Level
NOTES:
1. Each channel.
CIN
CI-O
∆vF
∆TA
RI-0
RI-I
II-I
CMH
CML
60
1.5
-1.8
1012
10 12
0.5
500
1000
500
1000
pF
VF = 0, f = MHz, ta = 25°C
1
pF
f = 1MHz, ta = 25°C
1, 5
mV/°C
IF = 1.6mA
1
Ω
VI—O = 500V, ta = 25°C
1, 5
Ω
VI—I = 500V, ta = 25°C
6
nA
Relative Humidity = 45%
6
VI—I = 500V, t = 5s
V/µs
VCM = 50V P-P ,VCC = 5.0V,
7,9
RL = 1.5kΩ, IF = OmA
V/µs
VCM = 50V P-P ,VCC = 5.0V,
8,9
RL = 1.5kΩ, IF = 1.6mA
2. CURRENT TRANSFER RATIO is defined as the ratio of output collector current, IO, to the forward LED input current., IF , times 100%.
3. IF = 2µA for channel under test. For all other channels, IF = 10mA.
4. Device considered a two-terminal device. Pins 1-6 and 16 are shorted together and pins 7-14 are shorted together.
5. Measured between each input pair shorted together.
6. Measured between adjacent pairs shorted together, i.e. between pins 1 and 2 shorted together and pins 3 and 4 shorted together, etc.
7. CMH is the maximum tolerable common mode transient to assure that the output will remain in a high logic state (ie. VO > @.0V).
8. CML is the maximum tolerable common mode transient to assure that the output will remain in a low logic state (ie. VO < 0.8V).
9. In applications where dv/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, RCC , should be included to protect the detector IC”s
from destructively high surge currents. The recommended value is RCC = 1V = kΩ
0.6IF (mA)
RECOMMENDED OPERATING CONDITIONS:
PARAMETER
SYMBOL
MIN
MAX
UNITS
Input Current, Low Level
IFL
0
2
µA
Input Current, High Level
IFH
0.5
5
mA
Supply Voltage
VCC
2.0
18
V
SELECTION GUIDE
PART NUMBER
PART DESCRIPTION
66012-001
66012-002
66012-003
66012-004
DSCC Dwg 8302401EX Quad Channel Optocoupler
Quad Channel optocoupler, commercial, tested over full military temperature range (-55°C to +125°C)
Quad Channel optocoupler, commercial (0° to +70°C)
Quad Channel optocoupler, commercial (-40°C to +85°C)
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918
www.micropac.com E-MAIL: optosales@micropac.com
3 - 28
Share Link: 