PI6C39912 Ver la hoja de datos (PDF) - Pericom Semiconductor Corporation
Número de pieza
componentes Descripción
Lista de partido
PI6C39912
Pericom Semiconductor Corporation
PI6C39912 Datasheet PDF : 11 Pages
| |||
PI6C39911/PI6C39912
3.3V High Speed LVTTL or Balanced Output
11223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677889900112233445566778899001122112233445566778899001122P3344r5566o77g8899r00a1122m3344m556677a88b9900l11e2211S2233k44e5566w7788C990011l22o33c44k556677B8899u0011f22f33e44r5566-7788S99u0011p2211e22r33C4455l66o7788c99k0011®22
Capacitance(6)
Parameter
Description
Test Conditions
Max.
Units
CIN
Input Capacitance
TA = 25°C, f = 1MHz, VCC = 3.3V
10
pF
Electrical Characteristics (Over the Operating Range)
Parameter
Description
Test Conditions
Min.
Max. Units
VOH Output HIGH Voltage
VOL Output LOW Voltage
VIH
Input HIGH Voltage
(REF and FB inputs only)
VCC = Min., IOH = 18mA
VCC = Min., IOL = 35mA
2.4
0.45
2.0
VCC
VIL
VIHH
Input LOW Voltage
(REF and FB inputs only)
Three-Level Input HIGH Voltage
(Test, FS, xFn)(4)
Min. ≤ VCC ≤ Max.
0.5
0.8
V
0.87 VCC VCC
VIMM
Three-Level Input MID Voltage
(Test, FS, xFn)(4)
Min. ≤ VCC ≤ Max.
0.47 VCC 0.53 VCC
VILL
Three-Level Input LOW Voltage
(Test, FS, xFn)(4)
Min. ≤ VCC ≤ Max.
0.0 0.13 VCC
IIH
Input HIGH Leakage Current
(REF and FB inputs only)
VCC = Max., VIN = Max.
20
IIL
Input LOW Leakage Current
(REF and FB inputs only)
IIHH Input HIGH Current (Test, FS, xFn)
IIMM Input MID Current (Test, FS, xFn)
VCC = Max., VIN = 0.4V
VIN = VCC
VIN = VCC/2
20
µA
200
50
50
IILL Input LOW Current (Test, FS, xFn)
IOS
Short Circuit Current(5)
ICCQ Operating Current Used by Internal
Circuitry
VIN = GND
VCC = Max., VOUT = GND (25°C only)
VCCN = VCCQ = Max.,
All Input Selects Open
Com'l
Mil/Ind
200
200
mA
95
100 mA
ICCN Output Buffer Current per Output Pair
PD Power Dissipation per Output Pair
VCCN = VCCQ = Max., IOUT = 0mA
All Input Selects Open, fMAX
VCCN = VCCQ = Max., IOUT = 0mA
All Input Selects Open, fMAX
25
mA
130 mW
Notes:
4. These inputs are normally wired to VCC, GND, or left unconnected (actual threshold voltages vary as a percentage of VCC).
Internal termination resistors hold unconnected inputs at VCC/2. If these inputs are switched, the function and timing of the
outputs may glitch and the PLL may require an additional tLOCK time before all data sheet limits are achieved.
5. PI6C39911 should be tested one output at a time, output shorted for less than one second, less than 10% duty cycle.
Room temperature only.
6. Applies to REF and FB inputs only. Tested initially and after any design or process changes that may affect these parameters.
7. Test measurement levels for the PI6C39911 are TTL levels (1.5V to 1.5V). Test conditions assume signal transition times of 2ns or less
and output loading as shown in the AC Test Loads and Waveforms unless otherwise specified.
8. Guaranteed by statistical correlation.
4
PS8497A 04/10/01
Share Link: