HI5667 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Lista de partido
HI5667 Datasheet PDF : 10 Pages
| |||
HI5667
Absolute Maximum Ratings TA = 25oC
Supply Voltage, AVCC or DVCC to AGND or DGND . . . . . . . . . . 6V
DGND to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3V
Digital I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DGND to DVCC
Analog I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . AGND to AVCC
Operating Conditions
Temperature Range
HI5667/xCx (Typ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
SSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
ACVL C=C10=pDFV; CTAC1==255o.0CV;,DDifVfeCrCen2t=ial3A.0nVa;loVgRIEnFpIuNt;=TVypRiEcaFlOVUaTl;ufeSs
= 60MSPS at 50% Duty Cycle;
are Test Results at 25oC,
Unless Otherwise Specified
PARAMETER
ACCURACY
Resolution
Integral Linearity Error, INL
Differential Linearity Error, DNL
(Guaranteed No Missing Codes)
Offset Error, VOS
Full Scale Error, FSE
DYNAMIC CHARACTERISTICS
Minimum Conversion Rate
Maximum Conversion Rate
Effective Number of Bits, ENOB
Signal to Noise and Distortion Ratio, SINAD
= ----------------R----M-----S------S----i-g----n---a---l---------------
RMS Noise + Distortion
TEST CONDITIONS
fIN = 10MHz
fIN = 10MHz
fIN = 10MHz
fIN = 10MHz
No Missing Codes
No Missing Codes
fIN = 10MHz
fIN = 10MHz
MIN TYP MAX
8
-
-
-
±0.3 ±1.75
-
±0.3 ±1.0
-10
-
10
-
1
-
-
0.5
1
60
7.3
7.7
-
-
48
-
Signal to Noise Ratio, SNR
= R-----M-----S------S----i-g---n----a---l
RMS Noise
fIN = 10MHz
Total Harmonic Distortion, THD
2nd Harmonic Distortion
3rd Harmonic Distortion
Spurious Free Dynamic Range, SFDR
Transient Response
fIN = 10MHz
fIN = 10MHz
fIN = 10MHz
fIN = 10MHz
(Note 2)
Over-Voltage Recovery
0.2V Overdrive (Note 2)
ANALOG INPUT
Maximum Peak-to-Peak Differential Analog Input Range
(VIN+ - VIN-)
Maximum Peak-to-Peak Single-Ended
Analog Input Range
Analog Input Resistance, RIN
Analog Input Capacitance, CIN
Analog Input Bias Current, IB+ or IB-
Differential Analog Input Bias Current
IBDIFF = (IB+ - IB-)
Full Power Input Bandwidth, FPBW
(Note 3)
(Note 3)
(Note 3)
Analog Input Common Mode Voltage Range (VIN+ + VIN-) / 2 Differential Mode (Note 2)
INTERNAL REFERENCE VOLTAGE
Reference Voltage Output, VREFOUT (Loaded)
Reference Output Current, IREFOUT
-
48.2
-
-
-62
-
-
-69
-
-
-63
-
-
63
-
-
1
-
-
1
-
-
±0.5
-
-
1.0
-
-
1
-
-
10
-
-10
-
+10
-
±0.5
-
-
250
-
0.25
-
4.75
-
2.5
-
-
1
2
UNITS
Bits
LSB
LSB
LSB
LSB
MSPS
MSPS
Bits
dB
dB
dBc
dBc
dBc
dBc
Cycle
Cycle
V
V
MΩ
pF
µA
µA
MHz
V
V
mA
4
Share Link: 