LTC1390CS Ver la hoja de datos (PDF) - Linear Technology
Número de pieza
componentes Descripción
Lista de partido
LTC1390CS Datasheet PDF : 8 Pages
| |||
LTC1390
UU W U
APPLICATIO S I FOR ATIO
transmission. Table 1 shows the various bit combinations
for channel selection.
Table 1. Logic Table for Channel Selection
CHANNEL STATUS
EN
B2
B1
B0
All Off
0
X
X
X
S0
1
0
0
0
S1
1
0
0
1
S2
1
0
1
0
S3
1
0
1
1
S4
1
1
0
0
S5
1
1
0
1
S6
1
1
1
0
S7
1
1
1
1
Digital Data Transfer Operation
The block diagram of Figure 3 shows the components
contained within the LTC1390 required for digital data
transfer. Digital data transfer operation can be performed
from Data 1 to Data 2 and vice versa as shown in Figure 4.
When CS is high, Buffer 1 is enabled and Buffer 2 is
disabled. The digital input data is fed into the 4-bit shift
register and then shifted to the MUX switches for channel
CLK
4-BIT SHIFT
REGISTER
MUX
SWITCHES
BUFFER 1
DATA 2
CS
DATA 1
BUFFER 2
LTC1390 • F03
Figure 3. Simplified Block Diagram of the Digital Data
Transfer Operation
CLK
1234
CS
Hi-Z
DATA 1
DATA OUT
DATA IN
DATA 2
DATA IN
DATA OUT
LTC1390 • F04
Figure 4. Digital Data Transfer Operation
6
selection or to Data 2 via Buffer 1 for data transfer. Data
appears at Data 2 after the fourth rising edge of the clock.
When CS is low, Buffer 2 is enabled and Buffer 1 is
disabled, thus digital input data is directly transferred from
Data 2 to Data 1 without any clock delay.
Multiplexer Expansion
Several LTC1390s can be daisy-chained to expand the
number of multiplexer inputs. No additional interface
ports are required for the expansion. Figure 5 shows two
LTC1390s connected at their analog outputs to form a 16-
to-1 multiplexer at the input to an LTC1286 A/D converter.
VCC VEE
VCC
1 S0
V + 16
2 S1 LTC1390 D 15
3 S2 A V – 14
4
ANALOG S3
INPUTS 5 S4
13
DATA 2
DATA 1 12
6 S5
CS 11
7 S6
CLK 10
8 S7
GND 9
1 S0
V + 16
2
15
S1 LTC1390 D
3
S2
B
V – 14
ANALOG 4 S3
INPUTS 5 S4
DATA 2 13
DATA 1 12
6 S5
CS 11
7 S6
CLK 10
8 S7
GND 9
1
VREF
8
VCC
2
+IN
7
CLK
3
LTC1286
6
–IN
DOUT
4
GND
5
CS
VCC
47k
DATA
CS
CLK
LTC1390 • F05
Figure 5. Daisy-Chaining Two LTC1390s for Expansion
To ensure that only one channel is switched on at any one
time, two sets of channel selection bits are needed for Data
as shown in Figure 6. The first data sequence is used to
switch off one MUX and the second data sequence is used
to select one channel from the other MUX, or vice versa.
In other words, if bit “ENA” is high and bit “ENB” is low,
one channel of MUX A is switched on and all channels of
MUX B are switched off. If bit “ENA” is low and bit “ENB”
is high, all channels of MUX A are switched off and one
channel of MUX B is switched on.
sn1390 1390fs
Share Link: 