FBL2031BB Ver la hoja de datos (PDF) - Philips Electronics

Número de pieza

componentes Descripción

Lista de partido

FBL2031BB

9-bit BTL 3.3V latched/registered/pass-thru Futurebus+ transceiver

Philips Electronics 

Philips Semiconductors

9-bit BTL 3.3V latched/registered/pass-thru

Futurebus+ transceiver

Product specification

FBL2031

DC ELECTRICAL CHARACTERISTICS

Over recommended operating free-air temperature range unless otherwise noted.

SYMBOL

PARAMETER

TEST CONDITIONS1

LIMITS

MIN

TYP2

MAX

UNIT

IOH

High level output current B0 – B8

VCC = MAX, VIL = MAX, VOH = 1.9V

100

µA

IOFF Power-off output current B0 – B8

VCC = 0V, VIL = MAX, VOH = 1.9V

VCC = 0V, VIL = MAX, VOH = 1.9V @ 85°C

100

µA

300

VCC = MIN to MAX

VCC–0.2

V

VOH

High-level output

voltage

AO0 – AO83

VCC = MIN; IOH = -8mA

2.4

V

VCC = MIN; IOH = -32mA

2.0

V

AO0 – AO83

VOL

Low-level output voltage

B0 – B8

VCC = MIN; IOL = 16mA

VCC = MIN; IOL = 32mA

VCC = MIN, IOL = 4mA

VCC = MIN, IOL = 100mA

0.4

V

0.5

V

0.5

V

0.75

1.0 1.20

VIK

Input clamp voltage

VCC = MIN, II = IIK = –18mA

–0.85 –1.2

V

Control pins

VCC = 3.6V; VI = VCC or GND

±1.0

Control/

II

Input leakage current

AI0 – AI8

AI0 – AI8

VCC = 0V or 3.6V; VI = 5.5V

VCC = 3.6V; VI = VCC

10

µA

1

Note 4

VCC = 3.6V; VI = 0V

–5

VCC = MAX, VI = 1.9V

100

µA

IIH

High-level input current B0 – B8

VCC = MAX, VI = 3.5V, note 5

100

mA

VCC = MAX, VI = 3.75V @ –40°C

100

IIL

Low-level input current B0 – B8

VCC = MAX, VI = 0.75V

–100 µA

IOZH Off-state output current AO0 – AO8

VCC = MAX, VO =3V

5

µA

IOZL Off-state output current AO0 – AO8

VCC = MAX, VO = 0.5V

–5

µA

ICCH B to A

VCC = MAX, outputs High

18

32

mA

ICCL B to A

VCC = MAX, outputs Low

22

37

mA

ICC

Supply current (total)

ICCH A to B

VCC = MAX, outputs High

11

16

mA

ICCL A to B

VCC = MAX, outputs Low

11

16

mA

ICCZ

VCC = MAX

18

32

mA

NOTES:

1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operation conditions for the applicable type.

2. All typical values are at VCC = 3.3V, TA = 25°C.

3. Due to test equipment limitations, actual test conditions are VIH = 1.8V and VIL = 1.3V for the B side.

4. Unused pins are at VCC or GND.

5. For B port input voltage between 3 and 5 volt; IIH will be greater than 100mA but the part will continue to function normally (clamping circuit

is active). This is not a tested condition.

2000 Apr 18

8

Share Link: