AN8000 Ver la hoja de datos (PDF) - Panasonic Corporation
Número de pieza
componentes Descripción
Lista de partido
AN8000 Datasheet PDF : 7 Pages
| |||
s Electrical Characteristics (Ta=25˚C)
· AN8009/AN8009M (9V Type)
Parameter
Symbol
Condition
min typ max Unit
Output voltage
Line regulation
Load regulation
VO
REGIN
REGL
Tj=25˚C
VI=9.5 to 15V, Tj=25˚C
IO=1 to 40mA, Tj=25˚C
IO=1 to 50mA, Tj=25˚C
8.64
9 9.36
V
9 100 mV
17
70 mV
37
75 mV
Minimum I/O voltage difference
VDIF (min.)
VI=8.8V, IO=20mA, Tj=25˚C
VI=8.8V, IO=50mA, Tj=25˚C
0.07 0.2
V
0.14 0.3
V
Bias current
Ripple rejection ratio
Output noise voltage
Output voltage temperature coefficient
Ibias
RR
Vno
∆VO/Ta
IO=0mA, Tj=25˚C
VI=10 to 12V, f=120Hz
f=10Hz to 100kHz
Tj=–30 to+125˚C
0.8
47
59
150
0.45
1.4 mA
dB
µV
mV/˚C
Note1) The specified condition Tj=25˚C means that the test should be conducted with each test time reduced (within 10ms) so that
the drift in characteristic value due to a temperature rise at chip junction can be ignored.
Note2) Unless otherwise specified, VI=10V, IO=20mA, CO=10µF
· AN8010/AN8010M (10V Type)
Parameter
Symbol
Condition
min typ max Unit
Output voltage
Line regulation
Load regulation
VO
REGIN
REGL
Tj=25˚C
VI=10.5 to 16V, Tj=25˚C
IO=1 to 40mA, Tj=25˚C
IO=1 to 50mA, Tj=25˚C
9.6
10 10.4
V
10 100 mV
18
75 mV
40
85 mV
Minimum I/O voltage difference
VDIF (min.)
VI=9.8V, IO=20mA, Tj=25˚C
VI=9.8V, IO=50mA, Tj=25˚C
0.07 0.2
V
0.14 0.3
V
Bias current
Ripple rejection ratio
Output noise voltage
Output voltage temperature coefficient
Ibias
RR
Vno
∆VO/Ta
IO=0mA, Tj=25˚C
VI=11 to 13V, f=120Hz
f=10Hz to 100kHz
Tj=–30 to+125˚C
0.8 1.4 mA
46
58
dB
165
µV
0.5
mV/˚C
Note1) The specified condition Tj=25˚C means that the test should be conducted with each test time reduced (within 10ms) so that
the drift in characteristic value due to a temperature rise at chip junction can be ignored.
Note2) Unless otherwise specified, VI=11V, IO=20mA, CO=10µF
s Application Circuit
Vin
0.33µF
AN8000
AN8000M
Vout
+
10µF
–
The AN8000/AN8000M series has IC internal gain increased in order to improve
performance. When the power line on the output side is long, use a capacitor of
10µF.
For the capacitor on the output side, attach it as close to the IC as possible.
When using at a low temperature, it is recommended to use the capacitors with
low internal impedance (for example, tantalum capacitor) for output capacitors.
Share Link: 