IDT54FCT162244AT Ver la hoja de datos (PDF) - Integrated Device Technology
Número de pieza
componentes Descripción
Lista de partido
IDT54FCT162244AT Datasheet PDF : 9 Pages
| |||
IDT54/74FCT16244T/AT/CT/ET, 162244T/AT/CT/ET,
166244T/AT/CT, 162H244T/AT/CT/ET FAST CMOS 16-BIT BUFFER/LINE DRIVER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ABSOLUTE MAXIMUM RATINGS(1)
FUNCTION TABLE(1)
Symbol
Description
VTERM(2) Terminal Voltage with Respect to
GND
VTERM(3) Terminal Voltage with Respect to
GND
TSTG Storage Temperature
Max.
–0.5 to +7.0
–0.5 to
VCC +0.5
–65 to +150
Unit
V
V
°C
IOUT DC Output Current
–60 to +120 mA
NOTES:
2544 lnk 03
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
2. All device terminals except FCT162XXXT and FCT166XXXT output and
I/O terminals.
3. Output and I/O terminals for FCT162XXXT and FCT166XXXT.
xOE
Inputs
L
L
H
NOTE:
1. H = HIGH Voltage Level
X = Don’t Care
L = LOW Voltage Level
Z = High Impedance
xAx
L
H
X
Outputs
xYx
L
H
Z
2544 tbl 02
CAPACITANCE (TA = +25°C, f = 1.0MHz)
Symbol Parameter(1) Conditions Typ. Max. Unit
CIN
Input
VIN = 0V
3.5 6.0 pF
Capacitance
COUT Output
VOUT = 0V 3.5 8.0 pF
Capacitance
NOTE:
2544 lnk 04
1. This parameter is measured at characterization but not tested.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE (STANDARD PARTS)
Following Conditions Apply Unless Otherwise Specified:
Commercial: TA = –40°C to +85°C, VCC = 5.0V ± 10%; Military: TA = –55°C to +125°C, VCC = 5.0V ± 10%
Symbol
Parameter
Test Conditions(1)
Min. Typ.(2) Max. Unit
VIH
Input HIGH Level
Guaranteed Logic HIGH Level
2.0 —
—
V
VIL
Input LOW Level
Guaranteed Logic LOW Level
—
— 0.8
V
II H
Input HIGH Current (Input pins)(5) VCC = Max.
VI = VCC
—
—
±1 µA
Input HIGH Current (I/O pins)(5)
—
—
±1
II L
Input LOW Current (Input pins)(5)
VI = GND
—
—
±1
Input LOW Current (I/O pins)(5)
—
—
±1
IOZH
High Impedance Output Current VCC = Max.
VO = 2.7V
—
—
±1 µA
IOZL
(3-State Output pins)(5)
VO = 0.5V
—
—
±1
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18mA
— –0.7 –1.2 V
IOS
Short Circuit Current
VCC = Max., VO = GND(3)
–80 –140 –225 mA
VH
Input Hysteresis
—
— 100 — mV
ICCL
ICCH
ICCZ
Quiescent Power Supply Current VCC = Max., VIN = GND or VCC
—
5 500
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. Duration of the condition can not exceed one second.
5. The test limit for this parameter is ± 5µA at TA = –55°C.
µA
2544 lnk 05
5.2
3
Share Link: 