49LF002B Ver la hoja de datos (PDF) - Silicon Storage Technology
Número de pieza
componentes Descripción
Lista de partido
49LF002B Datasheet PDF : 43 Pages
| |||
2 Mbit / 3 Mbit / 4 Mbit LPC Firmware Flash
SST49LF002B / SST49LF003B / SST49LF004B
FEATURES:
SST49LF002B / 003B / 004B2Mb / 3Mb / 4Mb LPC Firmware memory
Data Sheet
• 2 Mbit, 3 Mbit, or 4 Mbit SuperFlash memory
array for code/data storage
– SST49LF002B: 256K x8 (2 Mbit)
– SST49LF003B: 384K x8 (3 Mbit)
– SST49LF004B: 512K x8 (4 Mbit)
• Conforms to Intel LPC Interface Specification 1.1
– Supports Single-Byte LPC Memory and
Firmware Memory Cycle Types
• Flexible Erase Capability
– Uniform 4 KByte sectors
– Uniform 16 KByte overlay blocks for
SST49LF002B
– Uniform 64 KByte overlay blocks for
SST49LF003B/004B
– Chip-Erase for PP Mode Only
• Single 3.0-3.6V Read and Write Operations
• Superior Reliability
– Endurance: 100,000 Cycles (typical)
– Greater than 100 years Data Retention
• Low Power Consumption
– Active Read Current: 6 mA (typical)
– Standby Current: 10 µA (typical)
• Fast Sector-Erase/Byte-Program Operation
– Sector-Erase Time: 18 ms (typical)
– Block-Erase Time: 18 ms (typical)
– Chip-Erase Time: 70 ms (typical)
– Byte-Program Time: 14 µs (typical)
– Chip Rewrite Time:
SST49LF002B: 4 seconds (typical)
SST49LF003B: 6 seconds (typical)
SST49LF004B: 8 seconds (typical)
– Single-pulse Program or Erase
– Internal timing generation
• Two Operational Modes
– Low Pin Count (LPC) interface mode for
in-system operation
– Parallel Programming (PP) mode for fast
production programming
• LPC Interface Mode
– LPC bus interface supporting byte Read and
Write
– 33 MHz clock frequency operation
– WP# and TBL# pins provide hardware write
protect for entire chip and/or top Boot Block
– Block Locking Registers for individual block
Write-Lock and Lock-Down protection
– JEDEC Standard SDP Command Set
– Data# Polling and Toggle Bit for End-of-Write
detection
– 5 GPI pins for system design flexibility
– 4 ID pins for multi-chip selection
• Parallel Programming (PP) Mode
– 11-pin multiplexed address and 8-pin data
I/O interface
– Supports fast In-System or PROM programming
for manufacturing
• CMOS and PCI I/O Compatibility
• Packages Available
– 32-lead PLCC all devices
For SST49LF004B only:
– 40-lead TSOP (10mm x 20mm)
• All non-Pb (lead-free) devices are RoHS compliant
PRODUCT DESCRIPTION
The SST49LF00xB flash memory devices are designed to
interface with host controllers (chipsets) that support a low-
pin-count (LPC) interface for BIOS applications. The
SST49LF00xB devices comply with Intel’s LPC Interface
Specification 1.1, supporting single-byte Firmware Memory
and LPC Memory cycle types.
The SST49LF00xB devices are backward compatible to
the SST49LF00xA Firmware Hub and the SST49LF0x0A
LPC Flash. In this document, FWH mode in the
SST49LF00xA specification is referenced as the Firmware
Memory Read/Write cycle and LPC mode in the
SST49LF0x0A specification is referenced as the LPC
Memory Read/Write cycle. Two interface modes are sup-
ported by the SST49LF00xB: LPC mode (Firmware Mem-
ory and LPC Memory cycle types) for in-system operations
and Parallel Programming (PP) mode to interface with pro-
gramming equipment.
The SST49LF00xB flash memory devices are manufac-
tured with SST’s proprietary, high-performance SuperFlash
technology. The split-gate cell design and thick-oxide tun-
neling injector attain greater reliability and manufacturability
compared with alternative approaches. The SST49LF00xB
devices significantly improve performance and reliability,
while lowering power consumption. The SST49LF00xB
devices write (Program or Erase) with a single 3.0-3.6V
power supply.
©2005 Silicon Storage Technology, Inc.
S71232-05-000
1/05
1
The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc.
Intel is a registered trademark of Intel Corporation.
These specifications are subject to change without notice.
Share Link: 