MD1320N Ver la hoja de datos (PDF) - Unspecified
Número de pieza
componentes Descripción
Lista de partido
MD1320N Datasheet PDF : 24 Pages
| |||
1 Using the MD1320N DC to DC Converter Power IC
Thank you for purchasing the MD1320N DC to DC Converter Power IC. This manual contains important
information on the safe use of the MD1320N. Your safety is most important to our company. Please read these
instructions carefully before using this device.
CAUTION
The improper use of this device can result in serious injury or death.
Expensive damage to this and other equipment can result. Failure to observe the cautions in this
Manual can also result in minor injuries and annoying equipment damage.
CAUTION
The MD1320N is intended for use with general electronic equipment (office automation, communication,
measurement, household, etc.) It is not intended for use with equipment whose failure might result in the death or
injury of those depending upon it (medical treatment, air navigation, railroad, cargo handling, nuclear power, etc.)
If you intend to use the MD1620F with other than the general equipment listed above, please consult with our
company.
Under no conditions attempt to repair or modify this device by yourself. Doing so can result in electric shock,
equipment breakage, fire, and unreliable (and dangerous) equipment operation.
Abnormal operating conditions may result in excessive voltage at the output terminal or excessive voltage drops
elsewhere in the device. Take steps to prevent load mishandling and breakage (overvoltage and overcurrent
prevention) at the final point in the equipment chain.
Overvoltage protection
The MD1320N is not equipped with an overvoltage protection function. In the event excessive voltage appears
within a module, the high input voltage may remain together with a high output voltage even when the equipment
is turned off. Smoke and flame may appear. To prevent this, be sure to install some sort of overvoltage protection
circuitry before using the equipment.
Before providing electrical power to the device, check that the polarity of the input and output terminals is correct
(check for misconnections). If circuit protection circuitry is cut off from the rest of the equipment, smoke and
flames may appear.
Be sure that input voltage level is maintained at the specified level. This may require the installation of a voltage
regulator to the input line. Voltage fluctuations may result in the appearance of smoke and flames.
If a breakdown or other abnormal condition occurs during equipment use, immediately stop power to the
equipment. Contact our company at your earliest possible convenience.
The information appearing in this Manual is the latest available at the time of publication. We reserve the right to make changes to the device without prior
notice. Therefore, your device may differ slightly from that described in this Manual.
Every effort has been made to make the information in this Manual accurate and reliable. However, our company takes no responsibility for injuries or
damage incurred when using the device as described in this Manual. Neither do we take responsibility for damages incurred as a result of patent or other
defined rights.
We do not give consent for a third person to use our patent or other rights based on this material. We do not guarantee these rights.
No part of this material may be reproduced or copied without the specific written consent of our company.
This device fully meets the reliability and quality control standards described in our company's catalog. If this device is to be used in a situation where its
misuse or failure might cause serious injury or death, consult with our company.
Reliability and quality control standards for this device are considered adequate when it is used with the following types of end equipment.
Computer - Office automation - Communication terminal - Measurement . Machine tools - Audio-visual - Games and other amusements - Household
appliance - Personal items - Industrial robot.
Special applications where the device may or may not be suitable include the following.
Transportation and conveyance (cargo loading) equipment- Primary communications equipment- Traffic signal control equipment - Fire and burglary alarms -
Various safety devices - Medical equipment
Other special applications where the device reliability is not considered high enough include the following.
Atomic energy control systems - Aviation equipment- Aeronautics and space equipment - Ocean depth sounding equipment - Life supportequipment
Our company makes a constant effort to improve the quality and reliability of our products. However, it is the customer,s responsibility to provide safety.
Take the appropriate steps to prevent personal injury, fire, and damage by providing redundancy equipment, fire containment equipment, and devices to
protect personnel and equipment from operational mistakes.
1
Share Link: 