Overview
The ATmega32U6/AT90USB64/128 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega32U6/AT90USB64/128 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.

FEATUREs
• High Performance, Low Power AVR® 8-Bit Microcontroller
• Advanced RISC Architecture
   – 135 Powerful Instructions – Most Single Clock Cycle Execution
   – 32 x 8 General Purpose Working Registers
   – Fully Static Operation
   – Up to 16 MIPS Throughput at 16 MHz
   – On-Chip 2-cycle Multiplier
• Non-volatile Program and Data Memories
   – 32/64/128K Bytes of In-System Self-Programmable Flash
      • Endurance: 100,000 Write/Erase Cycles
   – Optional Boot Code Section with Independent Lock Bits
      • USB Bootloader programmed by default in the Factory
      • In-System Programming by On-chip Boot Program hardware activated after
         reset
      • True Read-While-Write Operation
      • All supplied parts are preprogramed with a default USB bootloader
   – 1K/2K/4K (32K/64K/128K Flash version) Bytes EEPROM
      • Endurance: 100,000 Write/Erase Cycles
   – 2.5K/4K/8K (32K/64K/128K Flash version) Bytes Internal SRAM
   – Up to 64K Bytes Optional External Memory Space
   – Programming Lock for Software Security
• JTAG (IEEE std. 1149.1 compliant) Interface
   – Boundary-scan Capabilities According to the JTAG Standard
   – Extensive On-chip Debug Support
   – Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface
• USB 2.0 Full-speed/Low-speed Device and On-The-Go Module
   – Complies fully with:
   – Universal Serial Bus Specification REV 2.0
   – On-The-Go Supplement to the USB 2.0 Specification Rev 1.0
   – Supports data transfer rates up to 12 Mbit/s and 1.5 Mbit/s
• USB Full-speed/Low Speed Device Module with Interrupt on Transfer Completion
   – Endpoint 0 for Control Transfers : up to 64-bytes
   – 6 Programmable Endpoints with IN or Out Directions and with Bulk, Interrupt or
      Isochronous Transfers
   – Configurable Endpoints size up to 256 bytes in double bank mode
   – Fully independant 832 bytes USB DPRAM for endpoint memory allocation
   – Suspend/Resume Interrupts
   – Power-on Reset and USB Bus Reset
   – 48 MHz PLL for Full-speed Bus Operation
   – USB Bus Disconnection on Microcontroller Request
• USB OTG Reduced Host :
   – Supports Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
      for OTG dual-role devices
   – Provide Status and control signals for software implementation of HNP and SRP
   – Provides programmable times required for HNP and SRP
• Peripheral Features
   – Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
   – Two16-bit Timer/Counter with Separate Prescaler, Compare- and Capture Mode
   – Real Time Counter with Separate Oscillator
   – Four 8-bit PWM Channels
   – Six PWM Channels with Programmable Resolution from 2 to 16 Bits
   – Output Compare Modulator
   – 8-channels, 10-bit ADC
   – Programmable Serial USART
   – Master/Slave SPI Serial Interface
   – Byte Oriented 2-wire Serial Interface
   – Programmable Watchdog Timer with Separate On-chip Oscillator
   – On-chip Analog Comparator
   – Interrupt and Wake-up on Pin Change
• Special Microcontroller Features
   – Power-on Reset and Programmable Brown-out Detection
   – Internal Calibrated Oscillator
   – External and Internal Interrupt Sources
   – Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby
• I/O and Packages
   – 48 Programmable I/O Lines
   – 64-lead TQFP and 64-lead QFN
• Operating Voltages
   – 2.7 - 5.5V
• Operating temperature
   – Industrial (-40°C to +85°C)
• Maximum Frequency
   – 8 MHz at 2.7V - Industrial range
   – 16 MHz at 4.5V - Industrial range