PRODUCT DESCRIPTION
The SST49LF00xC flash memory devices are designed to interface with host controllers (chipsets) that support a low pin-count (LPC) interface for system firmware applications. The SST49LF00xC device complies with Intel’s LPC Interface Specification 1.1, supporting a Burst-Read (up to 128 bytes in a single operation) which enables a 15.6 MByte per second data transfer. The LPC interface operates with 5 signal pins versus 28 pins of a 8-bit parallel flash memory. This frees up pins on the ASIC host controller resulting in lower ASIC costs and a reduction in overall system costs due to simplified signal routing.

FEATURES:
• Organized as 512K x8 / 1M x8
• Conforms to Intel® LPC Interface Specification v1.1
   – Support Multi-Byte Firmware Memory Read/ Write Cycles
• Single 3.0-3.6V Read and Write Operations
• LPC Mode
   – 5-signal LPC bus interface for both in-system and factory programming using programmer equipment
   – Multi-Byte Read capability allowing 15.6 MB/s data transfer rate @ 33 MHz PCI clock
   - Firmware Memory Read cycle supporting 1, 2, 4, 16, and 128 Byte Read
   - Firmware Memory Write cycle supporting 1, 2, and 4 Byte Write
   – 33 MHz clock frequency operation
   – WP#/AAI and TBL# pins provide hardware Write protect for entire chip and/or top Boot Block
   – Block Locking Registers for individual block Read Lock, Write-Lock, and Lock-Down protection
   – 5 GPI pins for system design flexibility
   – 4 ID pins for multi-chip selection
   – Multi-Byte capability registers (read-only registers)
   – Status register for End-of-Write detection
   – Program-/Erase-Suspend Read or Write to other blocks during Program-/Erase-Suspend
• Two-cycle Command Set
• Security ID Feature
   – 256-bit Secure ID space
   - 64-bit Unique Factory Pre-programmed Device Identifier
   - 192-bit User-Programmable OTP
• Low Power Consumption
   – Active Read Current: 12 mA (typical)
   - Standby Current: 10 µA (typical)
• Protected Data Area
   – 12-KByte Protected Data Area space
   – Three 4-KByte User-Programmable flash memory sectors
   – Read-lock, write-lock and lock-down protection for each sector
• Superior Reliability
   – Endurance: 100,000 Cycles (typical)
   – Greater than 100 years Data Retention
• Uniform 4 KByte sectors
   – SST49LF004C: 11 Overlay Blocks:
   - one 16-KByte Boot Block
   - two 8-KByte Parameter Blocks
   - one 32-Kbyte Parameter Block
   - seven 64-KByte Main Blocks
   – SST49LF008C: 19 Overlay Blocks:
   - one 16-KByte Boot Block
   - two 8-KByte Parameter Blocks
   - one 32-Kbyte Parameter Block
   - 15 64-KByte Main Blocks
• Fast Sector-Erase/Program Operation
   – Sector-Erase Time: 18 ms (typical)
   – Block-Erase Time: 18 ms (typical)
   – Program Time: 7 µs (typical)
• Auto Address Increment (AAI) for Rapid Factory Programming (High Voltage Enabled)
   – RY/BY# pin for End-of-Write detection
   – Multi-Byte Program
   – Chip Rewrite Time: (typical)
   - SST49LF004C: 1 seconds
   - SST49LF008C: 2 seconds
• Packages Available
   – 32-lead PLCC
   – 32-lead TSOP (8mm x 14mm)
• All non-Pb (lead-free) devices are RoHS compliant