RF2658PCBA Ver la hoja de datos (PDF) - RF Micro Devices
Número de pieza
componentes Descripción
Lista de partido
RF2658PCBA Datasheet PDF : 10 Pages
| |||
RF2658
Pin Function Description
Interface Schematic
1
MODE
Selects between CDMA and FM mode. This is a digitally controlled
BIAS
input. A logic “high” (≥VCC-0.7VDC) selects CDMA mode. A logic “low”
(≥0.5VDC) selects FM mode. In FM mode, this switch enables the FM
amplifier and turns off the I&Q modulator. The impedance on this pin is
30 kΩ.
60 kΩ
MODE
60 kΩ
2
Q SIG
Baseband input to the Q mixer. This pin is DC coupled. The DC level of
BIAS
BIAS
0.6V must be supplied to this pin to bias the transistor. Input imped-
ance of this pin is 50kΩ minimum.
8 kΩ
8 kΩ
Q SIG
Q REF
5
3
Q REF
Reference voltage for the Q mixer. This voltage should be the same as See pin 2.
the DC voltage supplied to the Q SIG pin. For maximum carrier sup-
pression, DC voltage on this pin relative to the Q SIG DC voltage may
be adjusted. Input impedance of this pin is 50kΩ minimum.
4
I REF
Reference voltage for the I mixer. This voltage should be the same as See pin 5.
the DC voltage supplied to the I SIG pin. For maximum carrier suppres-
sion, DC voltage on this pin relative to the I SIG DC voltage may be
adjusted. Input impedance of this pin is 50kΩ minimum.
5
I SIG
Baseband input to the I mixer. This pin is DC coupled. The DC level of
BIAS
BIAS
0.6V must be supplied to this pin to bias the transistor. Input imped-
ance of this pin is 50kΩ minimum.
8 kΩ
8 kΩ
I SIG
I REF
6
GND1
Ground connection for all baseband circuits including bandgap, AGC,
flip-flop, modulator and FM amp. Keep traces physically short and con-
nect immediately to ground plane for best performance.
7
VCC1
Supply voltage for the LO1 flip-flop and limiting amp only. This supply is
isolated to minimize the carrier leakage. A 1nF external bypass capaci-
tor is required, and an additional 0.1µF will be required if no other low
frequency bypass capacitors are nearby. The trace length between the
pin and the bypass capacitors should be minimized. The ground side of
the bypass capacitors should connect immediately to ground plane.
The part is designed to work from 2.7V to 3.3V supply.
8
LO1+, FM+ One half of the balanced modulator LO1 input. The other half of the
input, LO1-, is AC grounded for single-ended input applications. The
frequency on these pins is divided by a factor of 2, hence the carrier
VCC1
frequency for the modulator becomes one half of the applied frequency.
The single-ended input impedance is 100Ω (balanced is 200Ω). This
100 Ω
pin is NOT internally DC blocked. An external blocking capacitor (1nF
recommended) must be provided if the pin is connected to a device
LO1+, FM+
with DC present. When FM mode is selected, the output of the flip-flop
divider circuit is switched to the AGC amplifier inputs and the modulator
mixers are not used. Note that the frequency deviation input here will
be reduced by a factor of two, due to the frequency divider operation.
9
LO1-, FM- One half of the balanced modulator LO1 input. In single-ended applica- See pin 8.
tions (100Ω input impedance), this pin is AC grounded with a 1nF
capacitor.
10
BG OUT Bandgap voltage reference. This voltage, constant over temperature
and supply variation, is used to bias internal circuits. A 1nF external
bypass capacitor is required.
Rev A8 010720
VCC1
100 Ω
LO1-, FM-
5-63
Share Link: 