SCN2661 Ver la hoja de datos (PDF) - Philips Electronics
Número de pieza
componentes Descripción
Lista de partido
SCN2661 Datasheet PDF : 19 Pages
| |||
Philips Semiconductors
Enhanced programmable communications
interface (EPCI)
Product specification
SCN2661/SCN68661
68661C (BRCLK = 5.0688MHz)
MR23–20
BAUD RATE
ACTUAL FREQUENCY 16X CLOCK
PERCENT ERROR
DIVISOR
0000
50
0.8kHz
—
6336
0001
75
1.2
—
4224
0010
110
1.76
—
2880
0011
134.5
2.1523
0.016
2355
0100
150
2.4
—
2112
0101
300
4.8
—
1056
0110
600
9.6
—
528
0111
1200
19.2
—
264
1000
1800
28.8
—
176
1001
2000
32.081
0.253
158
1010
2400
38.4
—
132
1011
3600
57.6
—
88
1100
4800
76.8
—
66
1101
7200
115.2
—
44
1110
9600
153.6
—
33
1111
19200
316.8
3.125
16
NOTE: 16X clock is used in asynchronous mode. In synchronous mode, clock multiplier is 1X and BRG can be used only for TxC.
OPERATION
The functional operation of the 68661 is programmed by a set of
control words supplied by the CPU. These control words specify
items such as synchronous or asynchronous mode, baud rate,
number of bits per character, etc. The programming procedure is
described in the EPCI programming section of the data sheet.
After programming, the EPCI is ready to perform the desired
communications functions. The receiver performs serial to parallel
conversion of data received from a modem or equivalent device.
The transmitter converts parallel data received from the CPU to a
serial bit stream. These actions are accomplished within the
framework specified by the control words.
Receiver
The 68661 is conditioned to receiver data when the DCD input is
Low and the RxEN bit in the commands register is true. In the
asynchronous mode, the receiver looks for High-to-Low (mark to
space) transition of the start bit on the RxD input line. If a transition
is detected, the state of the RxD line is sampled again after a delay
of one-half of a bit-time. If RxD is now high, the search for a valid
start bit is begun again. If RxD is still Low, a valid start bit is
assumed and the receiver continues to sample the input line at one
bit time intervals until the proper number of data bits, the parity bit,
and one stop bit have been assembled. The data are then
transferred to the receive data holding register, the RxRDY bit in the
status register is set, and the RxRDY output is asserted. If the
character length is less than 8 bits, the High order unused bits in the
holding register are set to zero. The parity error, framing error, and
overrun error status bits are strobed into the status register on the
positive going edge of RxC corresponding to the received character
boundary. If the stop bit is present, the receiver will immediately
begin its search for the next start bit. If the stop bit is absent
(framing error), the receiver will interpret a space as a start bit if it
persists into the next bit timer interval. If a break condition is
detected (RxD is Low for the entire character as well as the stop bit),
only one character consisting of all zeros (with the FE status bit SR5
set) will be transferred to the holding register. The RxD input must
return to a High condition before a search for the next start bit
begins.
Pin 25 can be programmed to be a break detect output by
appropriate setting of MR27-MR24. If so, a detected break will
cause that pin to go High. When RxD returns to mark for one RxC
time, pin 25 will go low. Refer to the Break Detection Timing
Diagram.
When the EPCI is initialized into the synchronous mode, the
receiver first enters the hunt mode on a 0 to 1 transition of RxEN
(CR2). In this mode, as data are shifted into the receiver shift
register a bit at a time, the contents of the register are compared to
the contents of the SYN1 register. If the two are not equal, the next
bit is shifted in and the comparison is repeated. When the two
registers match, the hunt mode is terminated and character
assembly mode begins. If single SYN operation is programmed, the
SYN DETECT status bit is set. If double SYN operation is
programmed, the first character assembled after SYN1 must be
SYN2 in order for the SYN DETECT bit to be set. Otherwise, the
EPCI returns to the hunt mode. (Note that the sequence
SYN1-SYN1-SYN2 will not achieve synchronization.) When
synchronization has been achieved, the EPCI continues to
assemble characters and transfer then to the holding register,
setting the RxRDY status bit and asserting the RxRDY output each
time a character is transferred. The PE and OE status bits are set
as appropriate. Further receipt of the appropriate SYN sequence
sets the SYN DETECT status bit. If the SYN stripping mode is
commanded, SYN characters are not transferred to the holding
register. Note that the SYN characters used to establish initial
synchronization are not transferred to the holding register in any
case.
External jam synchronization can be achieved via pin 9 by
appropriate setting of MR27-MR24. When pin 9 is an XSYNC input,
the internal SYN1, SYN1–SYN2, and DLE–SYN1 detection is
disabled. Each positive going signal on XSYNC will cause the
receiver to establish synchronization on the rising edge of the next
RxC pulse. Character assembly will start with the RxD input at this
edge. XSYNC may be lowered on the next rising edge of RxD. This
external synchronization will cause the SYN DETECT status bit to
be set until the status register is read. Refer to XSYNC timing
diagram.
1994 Apr 27
6
Share Link: 