Overview
The 3X38FTR 208-Pin SQFP is an eight-channel, single-chip complete transceiver designed specifically for dual-speed 10Base-T, 100Base-TX, and 100Base-FX switches and repeaters. It supports simultaneous operation in three separate IEEE * standard modes: 10Base-T, 100Base-TX, and 100Base-FX. The 3X38 uses 0.25 µm low-power CMOS to achieve extremely low power dissipation and operates from a single 3.3 V power supply.

FEATUREs
10 Mbits/s Transceiver
■ Compatible with IEEE 802.3 10Base-T standard
   for category 3 unshielded twisted-pair (UTP) cable.
■ Compatible with the reduced MII (RMII) specification of the RMII consortium version 1.2.
■ Selectable 7-pin RMII or 2-pin serial MII (SMII).
■ Autopolarity detection and correction.
■ Adjustable squelch level for extended line length
   capability (two levels).
■ On-chip filtering eliminates the need for external
   filters.
■ Half- and full-duplex operations.

100 Mbits/s TX Transceiver
■ Compatible with IEEE 802.3u PCS (clause 23),
   PMA (clause 24), autonegotiation (clause 28), and
   PMD (clause 25) specifications.
■ Compatible with the reduced MII (RMII) specification of the RMII consortium version 1.2.
■ Selectable 7-pin RMII, 2-pin SMII (serial MII).
■ Scrambler/descrambler bypass.
■ Selectable carrier sense signal generation (CRS)
   asserted during either transmission or reception in
   half duplex (CRS asserted during reception only in
   full duplex).
■ Full- or half-duplex operations.
■ On-chip filtering and adaptive equalization that
   eliminates the need for external filters.

100 Mbits/s FX Transceiver
■ Pseudo-ECL compatible input/output for 100Base-FX
   support (with fiber-optic signal detect).
■ Compatible with IEEE 802.3u 100Base-FX standard.
■ Reuses existing twisted-pair I/O pins for compatible
   fiber-optic transceiver pseudo-ECL (PECL)
   data:
   — No additional data pins required.
   — Reuses existing 3X38 pins for fiber-optic
      signal detect (FOSD) inputs.
■ Fiber mode automatically configures port:
   — Disables autonegotiation.
   — Disables 10Base-T.
   — Enables 100Base-FX far-end fault signaling.
   — Disables MLT-3 encoder/decoder.
   — Disables scrambler/descrambler.
■ FX mode enable is pin- or register-selectable on an
   individual per-port basis.

General
■ Low power dissipation (<0.4 W per port).
■ Autonegotiation (IEEE 802.3u, clause 28):
   — Fast link pulse (FLP) burst generator.
   — Arbitration function.
■ Supports the station management protocol and frame format (clause 22):
   — Basic and extended registers.
   — Supports next page mode.
   — Accepts preamble suppression.
   — Maskable status interrupts.
   — 12.5 MHz MDC clock rate.
■ Supports the following management functions via pins if MII station management is unavailable:
   — Speed select.
   — Scrambler/descrambler bypass.
   — Full duplex.
   — No link pulse mode.
   — Carrier sense select.
   — Autonegotiation.
   — FX mode select.
■ Single 50 MHz/125 MHz clock input in RMII and SMII modes, respectively.
■ Supports half- and full-duplex operations.
■ Provides four LED status signals:
   — Activity (transmit or receive). Optional LED blink mode (500 ms on, 500 ms off or 2.5 s on, 2.5 s off) or pulse stretch mode (40 ms—80 ms).
   — Full duplex or collision, automatically configured.
   — Link integrity.
   — Speed indication.
■ Internally generated power-on-reset configures 3X38 automatically on powerup.
■ Serial LED output stream for additional status monitoring.
■ Bicolor LED mode.
■ LED drivers on-chip (8 mA—10 mA). Drivers can be turned off when LED is not used (power saving).
■ Per-channel powerdown mode for 10 Mbits/s and 100 Mbits/s operation.
■ Loopback for 10 Mbits/s and 100 Mbits/s operation.
■ Internal pull-up or pull-down resistors to set default configuration during powerup.
■ 0.25 µm low-power CMOS technology.
■ 208-pin SQFP package.
■ JTAG boundary scan.
■ Single 3.3 V power supply